User manual Hotpoint Washer BHWM 149

If you found this page, you probably have a problem and you need a user manual for the device Hotpoint Washer BHWM 149. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Hotpoint Washer BHWM 149 it belongs to the category Washer. A user manualHotpoint Washer BHWM 149 is taken from the manufacturer, a Hotpoint company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Hotpoint Washer BHWM 149 directly. You can view the user manualHotpoint Washer BHWM 149 directly online or save and store it on your computer.

Using the Drilling Template.  
GB  
-
To trace the positions of the holes on the left-  
hand side of the panel, align the drilling tem-  
plate to the top left side of the panel using the  
lines traced on the extremities as a reference.  
-
To trace the positions of the holes on the  
right-hand side of the panel, align the drilling  
template to the top right side of the panel.  
-
Use an appropriately sized router to mill the  
holes for the two hinges, the rubber plug and  
the magnet.  
Fig. 8  
Fig. 9  
Accessories provided for the height  
adjustment.  
Mounding the Parts onto the Wooden  
Panel (Door).  
The following can be found  
inside the polystyrene lid  
-
Insert the hinges into the holes (the movable  
part of the hinge must be positioned facing  
away from the panel) and fasten them with  
the 4 type A screws.  
(
fig. 10): 2 crossbars (G), 1  
strip (M)  
the following can be found  
inside the appliance drum:  
-
Insert the magnet into the top hole on the  
opposite side of the hinges and fasten it with  
4
4
4
4
additional feet (H),  
screws (I),  
the two type B screws.  
-
Insert the rubber plug into the bottom hole.  
screws (R),  
nuts (L),  
The panel is now ready to be mounted onto  
the machine.  
2 plinth guides (Q)  
Fig. 10  
Mounting the Panel into the machine.  
Insert the nib of the hinge (indicated by the arrow  
in fig. 2) into the hole for the hinge and push the  
panel towards the front of the machine. Fasten  
the two hinges with the type D screws.  
Adjusting the appliance height.  
The height of the appliance can be adjusted (from  
8
15 mm to 835 mm), by turning the 4 feet.  
Should you require the appliance to be placed  
higher than the above height, you need to use  
the following accessories to raise it to up to  
Fastening the plinth guide.  
If the machine is installed at the end of a set  
of modular cabinets, mount either one or both  
of the guides for the base molding (as shown  
in fig. 8). Adjust them for depth based on the  
position of the base molding, and, if necessa-  
ry, fasten the base to the guides (fig. 9). This is  
how to assemble the plinth guide (fig. 8):  
Fasten angle P using screw R, insert plinth  
guide Q into the special slot and once it is  
in the desired position, lock it in place using  
angle P and screw R.  
8
70 mm:  
the two crossbars (G); the 4 feet (H); the 4  
screws (I); the 4 nuts (L) then perform the fol-  
lowing operations (fig. 11):  
remove the 4 original feet, place a crossbar G  
at the front of the appliance, fastening it in pla-  
ce using screws I (screwing them in where the  
original feet were) then insert the new feet H.  
Repeat the same operation at the back of the  
appliance.  
Now adjust feet H to raise or lower the applian-  
ce from 835 mm to 870 mm.  
Inserting the machine into the Cabinet.  
-
Push the machine into the opening, aligning  
Once you have reached the desired height, lock  
nuts L onto crossbar G.  
it with the cabinets (fig. 6).  
Regulate the adjustable feet to raise the  
machine to the appropriate height.  
-
To adjust the appliance to a height between  
8
70 mm and 900 mm, you need to mount  
-
To adjust the position of the wooden panel  
strip M, adjusting feet H to the required height.  
Insert the strip as follows:  
in both the vertical and horizontal directions,  
use the C and D screws, as shown in fig. 7.  
Important: close the lower part of the ap-  
pliance front by ensuring that the plinth rests  
against the floor.  
loosen the three screws N situated at the front  
of the Top cover of the appliance, insert strip M  
as shown in fig. 12, then fasten screws N.  
M
6
00 min  
5
95  
C
5
40  
G
D
n
5
70mi  
L
H
C
I
Fig. 6  
Fig. 7  
Fig. 11  
Fig. 12  
7

In addition to the user manual Hotpoint Washer BHWM 149, we also provide a support panel to help you solve your problems with Hotpoint Washer BHWM 149. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Hotpoint Washer BHWM 149. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Hotpoint Washer BHWM 149 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.