User manual Barco Automobile Accessories 26-0904004-00

If you found this page, you probably have a problem and you need a user manual for the device Barco Automobile Accessories 26-0904004-00. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Barco Automobile Accessories 26-0904004-00 it belongs to the category Automobile Accessories. A user manualBarco Automobile Accessories 26-0904004-00 is taken from the manufacturer, a Barco company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Barco Automobile Accessories 26-0904004-00 directly. You can view the user manualBarco Automobile Accessories 26-0904004-00 directly online or save and store it on your computer.

Phone: +1 (916) 859-2500  
Fax: +1 (916) 859-2515  
Technical Support: +1 (866) 374-7878  
Websites: www.barco.com  
EMEA Support  
Website: www.barco.com/support/eSupport.aspx  
Phone: 0800900410  
Barco Events USA  
1101 Trade Center Drive  
Rancho Cordova, CA  
5670 • USA  
1
9
www.events.barco.com  
Quick Start Guide  
Visibly yours  
S3D/Dual  
Ethernet  
Connect to Web  
Interface or  
DisplayPort  
Input  
Connect to  
DisplayPort  
sources.  
Composite  
Output  
Connect to NTSC/  
PAL composite  
video display.  
DVI-I Input with  
Loop-through  
Connect to DVI  
sources.  
Channel Options  
Connect to S3D and  
dual channel sources,  
invert sync signals.  
Audio I/O  
Connect to audio  
source.  
DVI-D Output  
Connect to DVI  
video display.  
external controller.  
AC  
Connect to AC  
power source.  
Analog Input  
with Loop-  
through  
Connect to  
HD-15 sources.  
HDMI  
SDI Input  
with Loop-  
through  
Connect to  
SD-SDI or HD-  
SDI sources.  
SDI  
Analog  
DisplayPort  
Genlock  
HDMI  
Output  
Connect to  
Input  
Connect to  
HDMI  
Output  
Connect to  
SDI display.  
Output  
Connect to  
analog  
Output  
Connect to  
DisplayPort  
display.  
Connect a  
reference signal  
such as black  
burst or  
HDMI display.  
sources.  
display.  
composite sync.  
Setting Up Outputs  
Setting up an LED Display  
Quick Install and Setup  
6
. Obtain the output format — If the primary  
output is connected to an HDMI, DVI-D,  
HD-15 or DisplayPort connector, obtain the  
output’s preferred resolution and frame rate  
using the Output Menu. This is the format the  
ImagePRO-II uses. (Chapter 4, “Using EDID  
Auto Config” section)  
10. Position and adjust the image — Use the LED Setup Menu to  
position the image on the LED wall or other display device, scale  
the image, adjust pan and zoom settings, and save your view.  
(Chapter 4, “Positioning an Image on the Display” section.)  
Getting Started  
1
2
3
. Connect power Ensure that power is  
properly connected to the ImagePRO-II.  
. Connect inputs — Connect all input sources to  
the ImagePRO-II.  
Setting Up Inputs  
1
1
1
1.Set and adjust inputs — Select inputs and make any necessary  
adjustments to color balance, timings, and so on. (Chapter 4,  
. Connect outputs — Connect the output(s) on  
the ImagePRO-II to your projector(s) or other  
target devices.  
7
8
9
. Adjust output format — If the primary output  
is connected to the composite video connector  
or one the SDI connectors, you can adjust the  
output format manually if necessary. (Chapter  
Configuring Inputs” section.)  
2.Save input configuration — After adjusting an input, save the  
input configuration. (Chapter 4, “Saving an Input Configuration”  
section.)  
4
5
. Turn on power — Turn on power to the  
ImagePRO-II, your projector(s), and to all  
peripheral equipment.  
4, “Setting Output Format” section)  
. Test output Turn on a test pattern, verify  
that you have an image, and make any  
necessary adjustments. When complete, turn  
off the test pattern. (Chapter 4, “Working with  
Test Patterns” section)  
3.Adjust and save system settings — Adjust system parameters  
such as VFD brightness, Ethernet settings, and HDCP  
. Factory reset If you are using the  
ImagePRO-II for the first time, or if you are using  
an ImagePRO-II that has just returned from an  
event, perform a full factory reset to restore  
default system configurations.  
parameters. (Chapter 4, “Using the System Menu” section.)  
. Save output configuration After  
completing output adjustments, save the  
output configuration.  
ImagePRO-II User’s Guide  
For complete details on all installation and operations procedures,  
please refer to the ImagePRO-II User’s Guide.  
PN 26-0904004-00 Rev 01  

In addition to the user manual Barco Automobile Accessories 26-0904004-00, we also provide a support panel to help you solve your problems with Barco Automobile Accessories 26-0904004-00. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Barco Automobile Accessories 26-0904004-00. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Barco Automobile Accessories 26-0904004-00 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.