User manual American Standard Tropic 7038.801

If you found this page, you probably have a problem and you need a user manual for the device American Standard Tropic 7038.801. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database American Standard Tropic 7038.801 it belongs to the category Indoor Furnishings. A user manualAmerican Standard Tropic 7038.801 is taken from the manufacturer, a American Standard company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device American Standard Tropic 7038.801 directly. You can view the user manualAmerican Standard Tropic 7038.801 directly online or save and store it on your computer.

Installation  
Instructions  
7
038.801  
TROPIC  
Spread Lavatory Faucet with  
Speed Connect™ Drain  
Congratulations on purchasing your American Standard  
faucet with Speed Connect drain, a feature found only on  
American Standard faucets.  
Certified to comply with ANSI A112.18.1  
M968892 Rev. 1.1  
Speed Connect™ Drain*  
Fewer parts, installs in less time  
Never needs adjustment  
Guaranteed to seal properly the first time, every time.  
*
Your new American Standard faucet is designed to work only with the Speed Connect drain.  
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.  
Recommended tools  
Screwdriver  
Channel Locks  
Adjustable Wrench  
Tubing Cutter  
Turn off hot and cold water  
supplies before beginning.  
INSTALL SPOUT  
CAUTION  
1
Fig.A.  
1
Insert SPOUT (1) and CABLE CONNECTOR (14) through center hole, making sure  
the SPOUT ESCUTCHEON (2) and SEAL WASHER (3) are properly seated.  
Assemble RUBBER WASHER (4), BRASS WASHER (5) and LOCKNUT (6) onto SPOUT  
SHANK (7) from under side of sink . Make sure SPOUT (1) is centered in the mounting  
hole and the slot in the BRASS WASHER (5) faces toward the rear of the sink.  
2
3
Tighten LOCKNUT (6) firmly. Fig. A.  
7
INSTALL VALVE BODY  
A
Place RUBBER RING (9) into ADAPTER (10).  
1
4
5
Install LOCKNUT (11) and RUBBER WASHER (12) onto VALVE BODY (13).  
From under side of mounting surface, install VALVE BODY (13) through valve  
mounting holes. Threads of VALVE BODY (13) should extent at least 5/16  
of a inch above mounting surface top. Fig. B. Thread ADAPTER (10)  
onto VALVE BODY (13) until snug against internal stop. If necessary, adjust  
LOCKNUT (11).  
Tighten LOCKNUT (11) with WRENCH (8) (supplied) to secure VALVE  
BODY (13). Repeat above steps for opposite VALVE BODY (13A).  
SLOT  
6
1
1
4
1
9
0
1
0
MOUNTING  
SURFACE  
9
5
/16'' MIN.  
1
3a  
1
1
2
1
Fig.B.  
1
2
1
1
1
3
13  
8
1

In addition to the user manual American Standard Tropic 7038.801, we also provide a support panel to help you solve your problems with American Standard Tropic 7038.801. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with American Standard Tropic 7038.801. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with American Standard Tropic 7038.801 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.