3
-271-628-15(1)
Power sources
Precautions
Troubleshooting
Discs that this unit CAN play
•
Audio CD
General
The power is not on.
•
CD-R/CD-RW (CD-DA*)
*CD-DA is the abbreviation for Compact Disc Digital Audio. It is a
recording standard used for Audio CDs.
• Connect the AC power cord to the wall outlet securely.
•
Make sure the batteries are inserted correctly.
Personal Audio System
Discs that this unit CANNOT play
• Replace all the batteries with new ones if they are weak.
• When you operate the unit on batteries, you cannot turn on the unit
using POWER on the remote.
•
•
CD-R/CD-RW other than those recorded in music CD format
CD-R/CD-RW of poor recording quality, CD-R/CD-RW that
has scratches or are dirty, or CD-R/CD-RW recorded with an
incompatible recording device
Operating Instructions
US
There is no audio.
•
Unplug the headphones when listening through speakers.
•
CD-R/CD-RW which is finalized incorrectly
Notes on discs
Noise is heard.
•
Someone is using a portable telephone or other equipment that
emits radio waves near the player.
1
to AC IN
2
to a wall outlet
•
Before playing, clean the CD with a
cleaning cloth. Wipe the CD from the
center out. If there is a scratch, dirt or
fingerprints on the CD, it may cause
tracking error.
Owner’s Record
The model number is located at the bottom and the serial number is located in the battery compartment.
Record these numbers in the space provided below. Refer to them whenever you call upon your Sony
dealer regarding this product.
Move the portable telephone, etc., away from the player.
Connect the AC power cord or insert six R14 (size C) batteries (not supplied) into the battery compartment .
iPod
There is no audio.
• Make sure the iPod is connected firmly.
• Adjust the VOLUME.
Notes
Model No. ZS-S2iP Serial No. ______________
• Replace the batteries when the OPR/BATT indicator dims or when the player stops operating.
Replace all the batteries with new ones. Before you replace the batteries, be sure to take out the CD from the player.
•
To use the player on batteries, disconnect the AC power cord from the player.
• Do not use solvents such as benzine, thinner, commercially
available cleaners or anti-static spray intended for vinyl LPs.
Operation is impossible.
•
Do not expose the CD to direct sunlight or heat sources such as hot
air ducts, nor leave it in a car parked in direct sunlight as there can
be a considerable rise in temperature inside the car.
Do not stick paper or sticker on the CD, nor scratch the surface of
the CD.
•
Make sure the iPod is connected firmly.
Preparing the remote
Insert two R6 (size AA) batteries (not supplied).
ZS-S2iP
Cannot charge iPod.
•
•
•
•
You cannot charge the iPod when the unit is using DC power
supply.
You cannot charge the iPod when “DC OUT” does not appear on
the display in radio mode.
©
2007 Sony Corporation Printed in China
After playing, store the CD in its case.
On safety
•
As the laser beam used in the CD player section is harmful to the
eyes, do not attempt to disassemble the casing. Refer servicing to
qualified personnel only.
CD player
The CD does not play or “no dISC” is displayed even
WARNING
WARNING
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following
measures:
• Should any solid object or liquid fall into the player, unplug the
player, and have it checked by qualified personnel before operating
it any further.
when a CD is in place.
•
•
Place the CD with the label surface up.
Clean the CD.
To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or
moisture.
Replacing batteries
•
Discs with non-standard shapes (e.g., heart, square, star) cannot be
played on this player. Attempting to do so may damage the player.
Do not use such discs.
• Take out the CD and leave the CD compartment open for about an
hour to dry moisture condensation.
With normal use, the batteries for the remote should last about six months. When the remote no longer operates the unit,
replace all the batteries with new ones.
•
•
The CD-R/CD-RW is blank.
There is a problem with the quality of the CD-R/CD-RW, recording
device or application software.
To reduce the risk of fire, do not cover the ventilation of the
apparatus with newspapers, tablecloths, curtains, etc. And do
not place lighted candles on the apparatus.
On power sources
•
For AC operation, use the supplied AC power cord; do not use any
other type.
• Replace all the batteries with new ones if they are weak.
The apparatus shall not be exposed to dripping or splashing
and no objects filled with liquids, such as vases, shall be
placed on the apparatus.
•
The player is not disconnected from the AC power source (mains)
as long as it is connected to the wall outlet, even if the player itself
has been turned off.
Unplug the player from the wall outlet when it is not to be used for
an extended period of time.
When the batteries are not to be used, remove them to avoid
damage that can be caused by battery leakage or corrosion.
The nameplate indicating operating voltage, power consumption,
etc., is located at the bottom.
The sound drops out.
• Reduce the volume.
Before using the unit
Falling asleep to music
•
•
Clean the CD, or replace it if the CD is badly damaged.
Place the player in a location free from vibration.
•
•
•
As the main plug is used to disconnect the unit from the
mains, connect the unit to an easily accessible AC outlet.
Should you notice an abnormality in the unit, disconnect the
main plug from the AC outlet immediately.
1
Play the music source you want.
–
–
–
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
To turn on/off the power
Press POWER .
• Clean the lens with a commercially available blower.
2
3
Press SLEEP to display “SLEEP.”
•
The sound may drop out or noise may be heard when using poor
quality CD-Rs/CD-RWs or if there is a problem with the recording
device or application software.
Press SLEEP to select the minutes until the
player goes off automatically.
Do not install the appliance in a confined space, such as a
bookcase or built-in cabinet.
To adjust the volume
Press VOLUME +, – .
–
Consult the dealer or an experienced radio/TV technician for
help.
On placement
•
Each time you press the button, the indication
changes as follows:
“60” “90” “120” “OFF” “10”
“20” “30”.
Do not leave the player in a location near heat sources, in a place
subject to direct sunlight, excessive dust or mechanical shock or in
a car subject to the direct rays of the sun.
Do not place the player on an inclined or unstable place.
Do not place anything within 10 mm of the side of the cabinet. The
ventilation holes must be unobstructed for the player to operate
properly and prolong the life of its components.
Since a strong magnet is used for the speakers, keep personal credit
cards using magnetic coding or spring-wound watches away from
the player to prevent possible damage from the magnet.
Radio
Reception is poor.
Do not expose the battery to excessive heat such as direct
sunlight, fire or the like.
To listen through headphones
Connect the headphones to the (headphones) jack .
CAUTION
•
Reorient the antenna to
improve FM reception.
•
•
You are cautioned that any changes or modifications not
expressly approved in this manual could void your authority to
operate this equipment.
Notes on DualDiscs
To reinforce the bass sound
Press MEGA BASS .
A DualDisc is a two sided disc product which mates DVD
recorded material on one side with digital audio material on
the other side. However, since the audio material side does not
conform to the Compact Disc (CD) standard, playback on this
product is not guaranteed.
To cancel the sleep function
Press POWER to turn off the power.
“
MEGA BASS” appears in the display.
•
To return to normal sound, press the button again.
PFleoasre creguisstetrothmis perordsuctinon ltihneeatUSA
http://www.sony.com/productregistration.
Proper registration will enable us to send you periodic
mailings about new product, services and other
important announcements. Registering your product will
also allow us to contact you in the unlikely event that the
product needs adjustment or modification. Thank you.
On operation
•
If the player is brought directly from a cold to a warm location, or
is placed in a very damp room, moisture may condense on the lens
inside the CD player section. Should this occur, the player will not
operate properly. In this case, remove the CD and wait about an
hour for the moisture to evaporate.
•
Reorient the player
itself to improve AM
reception.
Music discs encoded with copyright
For carrying the unit
Always remove the iPod and store the sliding tray when
carrying the unit.
protection technologies
This product is designed to playback discs that conform to the
Compact Disc (CD) standard. Recently, various music discs
encoded with copyright protection technologies are marketed
by some record companies. Please be aware that among those
discs, there are some that do not conform to the CD standard
and may not be playable by this product.
Cleaning the cabinet
•
The audio is weak or has poor quality.
Clean the cabinet, panel and controls with a soft cloth slightly
moistened with a mild detergent solution. Do not use any type of
abrasive pad, scouring powder, or solvent, such as alcohol or benzine.
•
Replace all the batteries with new ones if they are weak.
Important Safety Instructions
•
Move the player away from the TV.
1
2
3
4
5
6
)
)
)
)
)
)
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with dry cloth.
The picture of your TV becomes unstable.
• If you are listening to an FM program near the TV with an indoor
antenna, move the player away from the TV.
If you have any questions or problems concerning your player, please
consult your nearest Sony dealer.
CAUTION
Specifications
The use of optical instruments with this product will increase
eye hazard.
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC DISTORTION
With 4-ohm loads, both channels driven from 150 Hz - 10,000 Hz; rated 1 W
per channel-minimum RMS power, with no more than 10
distortion in AC operation.
Mass
Approx. 2.7 kg (5 lb. 15 oz) (incl. batteries)
Supplied accessory
Remote
The remote does not function.
• Replace all the batteries in the remote with new ones if they are
weak.
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
7) Do not block any ventilation openings.
Install in accordance with the manufacturer’s instructions.
%
total harmonic
AC power cord (1)
Remote control (1)
8
9
)
)
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
•
Make sure that you are pointing the remote at the remote sensor on
the unit.
Remove any obstacles in the path of the remote and the unit.
Make sure the remote sensor is not exposed to strong light such as
direct sunlight or fluorescent lamp light.
NOTICE FOR CUSTOMERS IN THE
U.S.A.
Other specifications
Design and specifications are subject to change without notice.
CD player section
System
Compact disc digital audio system
Laser diode properties
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at
Optional accessory
Sony MDR headphones series
•
•
Compatible iPod models
The compatible iPod models are as follows. Update your iPod to use the latest
software before you use it.
• Move closer to the unit when using the remote.
After trying the remedies, if you still have problems, unplug the AC
power cord or remove all the batteries. After all the indications in the
display disappear, plug the AC power cord or insert the batteries again.
If the problem persists, please consult your nearest Sony dealer.
a distance of
about 200 mm from the objective lens surface on the
optical pick-up block with 7 mm aperture.)
Number of channels
2
1
0) Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
1) Only use attachments/accessories specified by the
manufacturer.
2) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
Frequency response
2
0 Hz - 20,000 Hz +1/–2 dB
Wow and flutter
Below measurable limit
1
1
iPod nano
iPod nano 4th
5th generation
(video camera)
generation (video)
iPod section
DC out: 5V
MAX: 500mA
(AC only)
iPod touch 2nd
generation
This symbol is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute
a risk of electric shock to persons.
Radio section
Frequency range
FM: 87.5 MHz - 108 MHz
AM: 530 kHz - 1,710 kHz
Antennas
FM: Telescopic antenna
iPod nano 3rd
generation (video)
This symbol is intended to alert the user
to the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
AM: Built-in ferrite bar antenna
iPod classic
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
iPod touch 1st
generation
General
Speaker
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or has been
dropped.
Full range: 8 cm (3 1/
4 inches) dia., 4 Ω, cone type (2)
Outputs
Headphones jack (stereo minijack):
For 16 Ω 32 Ω impedance headphones
Input
The graphical symbols are at the bottom of the unit.
-
AUDIO IN jack (stereo minijack)
Power output
Class II equipment symbol
This symbol indicates that the unit has a
double insulation system.
1.7 W
+
1.7 W (at 4 Ω, 10% harmonic distortion)
iPod nano 2nd
generation
iPod nano 1st
generation
Power requirements
For player:
iPod 5th
generation (video)
(
aluminium)
1
9
20 V AC, 60 Hz
V DC, 6 R14 (size C) batteries
Power consumption
AC 17 W
Battery life
For player:
FM reception
Sony R14P: approx.
6 h
iPod mini
Sony alkaline LR14: approx. 20
h
iPod 4th generation
(color display)
iPod 4th
generation
CD playback
Sony R14P: approx. 1.5
h
Sony alkaline LR14: approx.
7 h
Dimensions
Approx. 360 mm × 141.5 mm × 240.5 mm (w/h/d)
14 inches × 5 inches × 9 /2 inches) (incl. projecting parts)
1
(
1
/
4
5
/
8
Have you got problems with your device? Ask a question - our users can help you