User manual American Standard CHANDLER 7048

If you found this page, you probably have a problem and you need a user manual for the device American Standard CHANDLER 7048. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database American Standard CHANDLER 7048 it belongs to the category Plumbing Product. A user manualAmerican Standard CHANDLER 7048 is taken from the manufacturer, a American Standard company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device American Standard CHANDLER 7048 directly. You can view the user manualAmerican Standard CHANDLER 7048 directly online or save and store it on your computer.

M A D E W I T H  
Installation  
Instructions  
CHANDLER™ KITCHEN SINK  
MODEL 7048  
Certified to comply with ANSI Z124.6  
U.S. Patent No. D-355,023  
Observe local plumbing and building codes.  
Thank you for selecting American-Standard...the benchmark  
of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--please  
read these instructions carefully before you begin.  
7
90753-100 REV A  
BEFORE YOU BEGIN...Unpack new sink and  
CUTOUT DIMENSIONS FOR SINK  
inspect carefully for damage. Replace the sink  
in its original packing carton to protect it until  
you are ready to begin installation.  
Locate and mark center lines of sink on countertop.  
Provide proper clearance under the countertop for  
the faucet supply lines and the structural parts of the  
cabinet.  
Recommended Tools & Materials  
By using the diagram below and measuring your sink,  
draw the outline of the sink onto the countertop. This  
is not the cutting outline.  
Putty Knife  
Pipe Wrench  
Basin Wrench  
Saber Saw  
Channel Locks  
Phillips Screwdriver  
Regular Screwdriver  
Adjustable Wrench  
Drill  
Plumbers' Putty or  
Caulking  
Tubing Cutter  
Tape Measure  
Hacksaw  
CUTOUT FOR NEW INSTALLATION  
3
6" (914mm)  
32" (813mm)  
1
267mm)  
0-1/2"  
(
2
559mm)  
2"  
AFTER THE CUTOUT IS DRAWN...  
(
1
Drill a clearance hole  
inside the cutout line  
as marked on the  
countertop.  
2
(533mm)  
1"  
Perimeter  
of sink  
1
/2" (13mm)TYP.  
CUTTING  
LINE  
SINK  
OUTLINE  
Cutout  
Perimeter  
of sink  
2
3
MODIFICATION REQUIRED TO FIT CHANDLER SINK  
INTO A STANDARD 33" X 22" SINK CUTOUT  
Cut opening on cut  
line inside the peri-  
meter of sink.  
3
5"  
(
889mm)  
1
-1/2"  
(
38mm)  
Cutout  
3
2"(813mm)  
9-1/2"(495mm)  
CENTER LINE  
1
0-1/2"  
(
267mm)  
1
Mount the faucet and  
drain assembly on the  
sink following the  
manufacturer's  
19-1/2"(495mm)  
21"  
(
533mm)  
instructions.  
CUTTING  
LINE  
1/2" (13mm)TYP.  
SINK  
OUTLINE  
Product names listed herein are trademarks of American Standard Inc. unless otherwise noted.  
Corian Dupont registered trademark  
©
American Standard Inc. 2004  
®

In addition to the user manual American Standard CHANDLER 7048, we also provide a support panel to help you solve your problems with American Standard CHANDLER 7048. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with American Standard CHANDLER 7048. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with American Standard CHANDLER 7048 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.