User manual American Standard 2100

If you found this page, you probably have a problem and you need a user manual for the device American Standard 2100. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database American Standard 2100 it belongs to the category Plumbing Product. A user manualAmerican Standard 2100 is taken from the manufacturer, a American Standard company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device American Standard 2100 directly. You can view the user manualAmerican Standard 2100 directly online or save and store it on your computer.

CADET 1.6 GPF ONE-PIECE TOILET  
2099/2100  
INSTALLATION  
INSTRUCTIONS  
Model 2100 - Elongated w/Seat, Model 2099 - Round Front, Seat Not Included  
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product  
is installed properly, please read these instructions carefully before you begin. (Certain installations may require  
professional help.) Also be sure your installation conforms to local codes.  
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!  
NOTE: Pictures may not exactly define contour of china and components.  
RECOMMENDED TOOLS AND MATERIALS  
Putty Knife  
Hacksaw  
Regular Screwdriver  
Wax Ring/Gasket  
Adjustable Wrench  
Sealant  
Tape Measure  
Carpenters Level  
Flexible Supply Tube Closet Bolts  
1
REMOVE OLD TOILET  
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.  
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!  
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.  
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.  
a.  
b.  
c.  
d.  
NOTE: Mounting surface must be clean and level before new toilet is installed!  
ROUGHING-IN DIMENSIONS:  
NOTE: Distance from wall to closet flange centerline must be as listed below:  
2
3
FINISHED WALL  
CLOSET FLANGE  
7
7
62mm  
30)  
(
3
97mm  
11mm  
(28)  
(15-5/8)  
A
CLOSET BOLTS  
6
79mm  
(
26-3/4)  
SUPPLY AS  
REQ'D  
FINISHED  
FLOOR  
7
9mm  
(
3-1/8)  
INSTALL CLOSET BOLTS  
Install closet bolts in flange channel, turn 90 , and slide  
into place 6" (152 mm) apart and parallel to wall.  
1
40mm  
*
3
05mm  
(12)  
(5-1/2)  
FINISHED  
FLOOR  
C/L OF OUTLET  
4
5
NUT  
WAX RING  
WASHER  
BOLT  
FLANGE  
SEALANT  
INSTALL WAX SEAL  
POSITION TOILET ON FLANGE  
Invert toilet on floor (cushion to prevent damage), and  
install wax ring evenly around waste flange (horn), with  
tapered end of ring facing toilet. Apply a thin bead of  
sealant around toilet base.  
a. Unplug floor waste opening and install toilet on closet flange so bolts project  
through mounting holes.  
b. Loosely install retainer washers and nuts. Side of washers marked "THIS  
SIDE UP" must face up!  
Saniwares  
730481-100 Rev. C  
Product names listed herein are trademarks of American Standard Inc.  
©
American Standard Inc. 2002  

In addition to the user manual American Standard 2100, we also provide a support panel to help you solve your problems with American Standard 2100. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with American Standard 2100. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with American Standard 2100 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.