User manual American Standard 2474

If you found this page, you probably have a problem and you need a user manual for the device American Standard 2474. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database American Standard 2474 it belongs to the category Plumbing Product. A user manualAmerican Standard 2474 is taken from the manufacturer, a American Standard company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device American Standard 2474 directly. You can view the user manualAmerican Standard 2474 directly online or save and store it on your computer.

THE  
IMNodSelT24A74LELlonAgaTteIdOTwNo PINiecSe TToRiletUCTIONS  
COL LE CT IO N  
by  
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product  
is installed properly, please read these instructions carefully before you begin. (Certain installations may require  
professional help.) Also be sure your installation conforms to local codes.  
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!  
NOTE: Pictures may not exactly define contour of china and components.  
RECOMMENDED TOOLS AND MATERIALS  
Putty Knife  
Hacksaw  
Regular Screwdriver  
Wax Ring/Gasket  
Adjustable Wrench  
Sealant  
Tape Measure  
Carpenters Level  
Flexible Supply Tube Closet Bolts  
1
REMOVE OLD TOILET  
Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.  
Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!  
Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.  
Remove closet bolts from flange and clean away old wax, putty, etc. from base area.  
a.  
b.  
c.  
d.  
NOTE: Mounting surface must be clean and level before new toilet is installed!  
2
ROUGHING-IN DIMENSIONS:  
3
FINISHED WALL  
CLOSET FLANGE  
A
CLOSET BOLTS  
FINISHED  
FLOOR  
INSTALL CLOSET BOLTS  
Install closet bolts in flange channel, turn 90°, and slide  
into place 6" (152 mm) apart and parallel to wall.  
1
2"  
(
305mm)  
C/L OF SUPPLY  
AS REQUIRED  
4
5
WAX RING  
SEALANT  
NUT  
TAPERED  
WASHER  
CLOSET  
BOLT  
FLANGE  
INSTALL WAX SEAL  
POSITION TOILET ON FLANGE  
Invert toilet on floor (cushion to prevent damage), and  
install wax ring evenly around waste flange (horn), with  
tapered end of ring facing toilet. Apply a thin bead of  
sealant around toilet base.  
a. Unplug floor waste opening and install toilet on closet flange so bolts project  
through mounting holes.  
b. Loosely install retainer washers and nuts. Side of washers marked "THIS  
SIDE UP" must face up!  
Product names listed herein are trademarks of American Standard Inc.  
©
American Standard Inc. 2002  
7
30517-100  

In addition to the user manual American Standard 2474, we also provide a support panel to help you solve your problems with American Standard 2474. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with American Standard 2474. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with American Standard 2474 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.