User manual American Standard CHAMPION 4 2004

If you found this page, you probably have a problem and you need a user manual for the device American Standard CHAMPION 4 2004. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database American Standard CHAMPION 4 2004 it belongs to the category Plumbing Product. A user manualAmerican Standard CHAMPION 4 2004 is taken from the manufacturer, a American Standard company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device American Standard CHAMPION 4 2004 directly. You can view the user manualAmerican Standard CHAMPION 4 2004 directly online or save and store it on your computer.

INSTALLATION INSTRUCTIONS  
®
Champion 4  
Model 2004 Normal Height Elongated One PieceToilet  
®
Model 2034 Right Height Elongated One PieceToilet  
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is installed properly,please read  
these instructions carefully before you begin.(Certain installations may require professional help.) Also be sure your installation conforms to local codes.  
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!  
NOTE: Pictures may not exactly define contour of china and components.  
NOTE: BACK-TO-BACK INSTALLATION  
Depending upon your plumbing and venting conditions, the flow from  
the Champion in a back-to-back installation may create a vacuum on  
the system and draw water from the opposing bowl. The National  
Standards Plumbing Code prohibits the use of a cross fitting for  
drainage as throw over is possible. The code does approve a  
directional "Y" style fitting with proper venting to direct the water  
downward and away from the other toilet.  
Recommended fitting type for back-to-back installations.  
RECOMMENDED TOOLS AND MATERIALS  
Regular Screwdriver  
Wax Ring/Gasket  
Adjustable Wrench  
Putty Knife  
Closet Bolts  
Sealant  
Hacksaw  
Carpenters Level  
Tape Measure  
Flexible Supply Tube  
1
2
REMOVE OLD TOILET  
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.  
b. Disconnect and remove supply line. NOTE: If replacing valve,first shut off main water supply!  
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.  
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.  
NOTE: Mounting surface must be clean and level before new toilet is installed!  
ROUGHING-IN DIMENSIONS:  
NOTE: Distance from wall to closet flange centerline must be as listed below:  
FINISHED WALL  
FINISHED WALL  
29-3/4  
2
9-3/4  
(
756mm)  
Model 2004  
(756mm)  
Model 2034  
1
-3/4 (44mm)  
1-3/4 (44mm)  
C/L OF SEAT  
POST HOLES  
-1/2 (140mm)  
C/L OF SEAT  
POST HOLES  
5-1/2 (140mm)  
CENTERS  
16-3/4  
1
6-3/4  
8
(203mm)  
8
203mm)  
(
425mm)  
(425mm)  
(
5
CENTERS  
1
8-1/2  
18-1/2  
(470mm)  
(
470mm)  
1
1
(25mm)  
(
25mm)  
1
7-3/4  
17-3/4  
SUPPLY  
AS  
(451mm)  
SUPPLY  
(451mm)  
29-1/2  
(749mm)  
28-1/8  
(714mm)  
AS  
REQ'D  
REQ'D  
1
5
16-1/2  
(419mm)  
(
381mm)  
4
102mm)  
3-3/4  
(95mm)  
7
178mm)  
7
(178mm)  
(
(
1
-1/4  
1/2  
1-1/4  
1/2  
4
-1/2  
*
4-1/2  
(
32mm) (13mm)  
*
FINISHED  
FLOOR  
(32mm)  
(13mm)  
FINISHED  
FLOOR  
(
114mm)  
(114mm)  
1
273mm)  
0-3/4  
13-1/2  
(343mm)  
10-3/4  
(273mm)  
13-1/2  
(343mm)  
(
10-3/4  
(273mm)  
10-3/4  
(273mm)  
1
2
1
2
(
305mm)  
C/L OF OUTLET  
C/L OF OUTLET  
(
305mm)  
3
4
5
CLOSET  
FLANGE  
NUT  
TAPERED  
WASHER  
A
CLOSET  
BOLTS  
CLOSET  
BOLT  
FLANGE  
SEALANT  
WAX RING  
INSTALL WAX SEAL  
INSTALL CLOSET BOLTS  
Install closet bolts in flange  
channel, turn 90°, and slide into  
place 6" (152mm) apart and  
parallel to wall.  
POSITION TOILET ON FLANGE  
a. Unplug floor waste opening and install toilet on closet  
flange so bolts project through mounting holes.  
b. Loosely install retainer washers and nuts. Side of  
washers marked "THIS SIDE UP" must face up!  
Invert toilet on floor (cushion to prevent  
damage), and install wax ring evenly  
around waste flange (horn), with tapered  
end of ring facing toilet. Apply a thin  
bead of sealant around toilet base.  
Pr o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .  
© A S A m e r i c a , I n c . 2 011  
7
30865-100 Rev. M  

In addition to the user manual American Standard CHAMPION 4 2004, we also provide a support panel to help you solve your problems with American Standard CHAMPION 4 2004. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with American Standard CHAMPION 4 2004. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with American Standard CHAMPION 4 2004 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.