User manual American Standard PORTSMOUTHTM 7420.901

If you found this page, you probably have a problem and you need a user manual for the device American Standard PORTSMOUTHTM 7420.901. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database American Standard PORTSMOUTHTM 7420.901 it belongs to the category Plumbing Product. A user manualAmerican Standard PORTSMOUTHTM 7420.901 is taken from the manufacturer, a American Standard company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device American Standard PORTSMOUTHTM 7420.901 directly. You can view the user manualAmerican Standard PORTSMOUTHTM 7420.901 directly online or save and store it on your computer.

Installation  
Instructions  
7420.900  
PORTSMOUTH™  
7
420.901  
Series  
DECK MOUNT  
BATH FILLER  
7
7
420.920  
420.921  
Series  
Thank you for selecting American-Standard...  
the benchmark of fine quality for over 100 years.  
To ensure that your installation proceeds smoothly--  
please read these instructions carefully before you begin.  
Certified to comply with ANSI A112.18.1M  
M965027 REV.1.6  
Recommended Tools  
ROUGHING-IN DIMENSIONS  
2-7/8"  
(73mm)  
CROSS HANDLE  
7
-7/8"  
6-1/2" to 12"  
(
199mm)  
(165mm to 305mm)  
2-1/4" D.  
(56mm) D.  
Flat Blade Screwdriver  
Tubing Cutter  
3
-3/16"  
8
-1/4"  
(
81mm)  
LEVER  
HANDLE  
(210mm)  
7
-7/8"  
(
200mm)  
2
-1/16" D.  
4
-7/8"  
(
52mm) D.  
(
125mm)  
Adjustable Wrench  
MOUNTING  
SURFACE  
*
Wrench  
1
-1/8 D.  
2
-5/8" D.  
3'  
(
66mm) D.  
(76mm)  
1
-1/2 MAX.  
1
-3/16" MAX.  
(38mm) MAX.  
(
30mm) MAX.  
1
-3/16 D.  
(
30mm) D.  
(H)  
(C)  
*
Hex key  
3/4-14 MALE  
N.P.T. INLETS  
Channel Locks  
1-1/16 D.  
(27mm) D.  
12 MAX.  
(305mm)  
*
Supplied with Fitting  
Turn off hot and cold water  
supplies before beginning.  
SPOUT ASSEMBLY  
CAUTION  
PREPARE TUBE AND TEE ASSEMBLY  
2
1
Install RUBBER RING (1) into recess of spout base.  
Prepare TUBE and TEE ASSEMBLY (1) to fit center to center  
VALVE (2) location (between 6-1/2" and 12"). If necessary,  
cut and/or bend TUBING carefully. Make sure tube bend is  
close to the TEE (1) so that it will not effect the compression  
joint at the VALVE CONNECTION.  
Insert SPOUT SHANK (2) through center hole of MOUNTING LEDGE.  
Make sure that the RUBBER RING (1) is properly seated in RECESS  
of SPOUT BASE.  
Assemble RUBBER WASHER (3) and BRASS WASHER (4) onto  
SHANK (2). From underside of ledge secure SPOUT (6) into position  
with LOCKNUT (5).  
Remove COUPLING NUT (3) and FERRULE (4) from each  
VALVE (2) and slide onto TUBING (5).  
4
3
1
5
3
4
6
-1/2" to 12"  
6
(
165mm to 305mm)  
RECESS  
2
1
MOUNTING  
SURFACE  
MOUNTING  
SURFACE  
3
5
4
2
NOTE  
VALVE inlet is  
3
/4-inch NPT male.  

In addition to the user manual American Standard PORTSMOUTHTM 7420.901, we also provide a support panel to help you solve your problems with American Standard PORTSMOUTHTM 7420.901. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with American Standard PORTSMOUTHTM 7420.901. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with American Standard PORTSMOUTHTM 7420.901 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.