User manual Whirlpool WFE540H0AS

If you found this page, you probably have a problem and you need a user manual for the device Whirlpool WFE540H0AS. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Whirlpool WFE540H0AS it belongs to the category Range. A user manualWhirlpool WFE540H0AS is taken from the manufacturer, a Whirlpool company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Whirlpool WFE540H0AS directly. You can view the user manualWhirlpool WFE540H0AS directly online or save and store it on your computer.

Odors and smoke are normal when the oven is used the first few  
times, or when it is heavily soiled.  
IMPORTANT: The health of some birds is extremely sensitive to the  
fumes given off. Exposure to the fumes may result in death to  
certain birds. Always move birds to another closed and well-  
ventilated room.  
Control Display  
Energy Save  
The display will flash when powered up or after a power loss. Press  
CANCEL to clear. When oven is not in use, the time of day is  
displayed, unless the range is in Energy Save mode. During Energy  
Save mode, the display will be blank. Indicator lights show  
functions that are in use.  
The Energy Save feature places the control and clock into a Sleep  
mode that reduces power consumption when the range is not  
being used.  
To enter the Energy Save mode, the oven and control must be idle  
with the Time of Day (TOD) shown on the display. Press and hold  
CLOCK for 10 seconds. The control will beep and the display will  
show the letters “ES” followed by “On” twice. The display will  
return to the TOD.  
Options Mode  
Press and hold TIMER for 5 seconds, and “Opt” will appear. Use  
the Temp/Time “up” or “down” arrow pads to cycle through the  
following options. Press CANCEL to exit the mode.  
If Energy Save mode is activated, each time the range is idle for  
minutes with only the Time of Day (TOD) shown, the display will  
show the letters “ES” followed by “On” twice. The display will then  
be blank until a control key is pressed or the oven door is opened.  
The control will then perform any of its operations in response to  
additional key presses.  
Fahrenheit and Celsius  
The temperature is preset at Fahrenheit, but can be changed to  
Celsius. Press TIMER to toggle between Fahrenheit and Celsius.  
Press CANCEL to exit.  
To exit Energy Save mode, press and hold the CLOCK key for  
10 seconds. The control will beep and the display will show the  
letters “ES” followed by “Off” twice. The display will return to the  
End of Cycle Tones  
b1” (beep once) or “b” (continue to beep) will be displayed. Press  
TIMER to toggle through selections. Press CANCEL to exit.  
Oven Light with Door Open  
Oven Temperature Control  
“LOn” indicates that the oven light will turn on when the door is  
open. If “LOFF” is displayed, the oven light will turn on only with the  
oven light switch. Press TIMER to toggle through selection. Press  
CANCEL to exit.  
IMPORTANT: Do not use a thermometer to measure oven  
temperature because opening the oven door may cause element  
cycling to give incorrect readings.  
2-Hour Shutoff  
The oven provides accurate temperatures; however, it may cook  
faster or slower than your previous oven, so the temperature can  
be adjusted to personalize it for your cooking needs. It can be  
changed in Fahrenheit or Celsius.  
If “12 Hr” is displayed, the oven will automatically shut off after  
shutoff. Press CANCEL to exit.  
2 hours. Press TIMER to toggle to “- - Hr” to disable the 12-hour  
To Adjust Oven Temperature:  
Press and hold BAKE for 5 seconds until the oven display  
shows the current setting, for example “0°F CAL” or “00.”  
Press the Temp/Time “up” or “down” arrow pads to increase or  
to decrease the temperature in 10°F (5°C or 6°C) amounts. The  
adjustment can be set between 30°F (17°C) and -30°F (-17°C).  
Tones are audible signals, indicating the following:  
Basic Functions  
One tone  
Valid pad press  
3. Press START.  
Oven is preheated (long tone)  
Function has been entered  
Reminder (on some models), repeating every 20 seconds after  
the end-of-cycle tones  
Three tones  
Invalid pad press  
Four tones  
End of cycle  

In addition to the user manual Whirlpool WFE540H0AS, we also provide a support panel to help you solve your problems with Whirlpool WFE540H0AS. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Whirlpool WFE540H0AS. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Whirlpool WFE540H0AS - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.