If you found this page, you probably have a problem and you need a user manual for the device Linear XR-D. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Linear XR-D it belongs to the category Satellite Radio. A user manualLinear XR-D is taken from the manufacturer, a Linear company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Linear XR-D directly. You can view the user manualLinear XR-D directly online or save and store it on your computer.
6
.
CONSTRUCT CABLE & CONNECT POWER
7. ASCII DATA OUTPUT DETAILS
8. MOUNT ANTENNA AND ROUTE CABLE
TRANSMIT DATA (TD)
DATA TERMINAL READY (DTR)
SIGNAL GROUND (SIG GND)
ANT-1A
USE ANT-1A ANTENNA
FOR SHORT RANGE (LESS
THAN 1 MILE)
APPLICATIONS
+
12 VDC
DATA OUTPUT PRODUCED WHEN PRESSING XR-D TEST BUTTON
ANTENNA
GROUND
A 65432 0001 21A0HX
XR-D SERIAL DATA OUTPUT STRING KEY
CON-180A
STRAIGHT
CONNECTOR
SIG GND
DTR
TD
P SSSSSS CCCC BTARVXE
+
12 VDC
CON-180A + CON-90A
ANGLE CONNECTOR
GROUND
P = PACKET TYPE CHARACTER (A OR B). XT TRANSMITTERS SEND FOUR ROUNDS
OF DATA EACH ACTIVATION. PACKET TYPE "A" IS FIRST ROUND, PACKET TYPE "B"
IS FOR THE NEXT THREE ROUNDS.
WARNING
THIS UNIT REQUIRES 12 VDC AT 1/2 AMP.
THE NO-LOAD VOLTAGE OF THE SUPPLY
MUST NOT EXCEED 17.5 VDC OR DAMAGE
TO THE UNIT WILL OCCUR!
S = FIVE-DIGIT DECIMAL NUMBER (00000 - 65535) THAT IS EQUAL TO THE BINARY
CODE SET ON THE TRANSMITTER'S SYSTEM CODE SWITCHES "A" & "B" . SYSTEM
CODE SWITCH "B", POSITION 8 IS THE LEAST SIGNIFICANT BINARY DIGIT, SWITCH
"
A" POSITION 1 IS THE MOST SIGNIFICANT BINARY DIGIT.
ROUTE WIRES THROUGH
CASE STRAIN RELIEF
BUSHING BEFORE
C = FOUR BINARY DIGITS (0 OR 1) INDICATING TRANSMITTER CHANNEL
ACTIVATED. 0=NO ALARM, 1=ALARM. ORDERED CH4, CH3, CH2, CH1.
XR-D TO FEMALE DB-9 FOR COMPUTER CABLE
CONNECTING TO TERMINALS
SIG GND
DTR
PIN 5 (SIG GND)
PIN 6 (DSR)
PIN 2 (RD)
B = ONE-DIGIT DECIMAL NUMBER (0 - 3) EQUAL TO THE BANK NUMBER (1-4) SET IN
THE TRANSMITTER.
USE 3-FOOT LONG ANT-2 ANTENNA FOR LONGER
RANGE APPLICATIONS OR DIFFICULT
INSTALLATIONS
TD
FEMALE
DB-9
+
12 VDC
GROUND
T = ONE-DIGIT DECIMAL NUMBER (0 - 2) DEFINING TRANSMITTER TYPE
(
0 = XT-1, 1 = XT-4, 2 = XT-2H OR XT-4H IN MULTI-CHANNEL MODE).
XR-D TO FEMALE DB-25 FOR COMPUTER CABLE
A = ALARM/RESTORE CHARACTER (A OR R). RELEVANT FOR SINGLE-CHANNEL
TRANSMITTERS ONLY.
SIG GND
DTR
PIN 7 (SIG GND)
PIN 6 (DSR)
PIN 3 (RD)
MOUNT ANTENNAS AS HIGH AS POSSIBLE
(A METAL MOUNTING POLE IS RECOMMENDED)
FEMALE
DB-25
TD
+
12 VDC
R = ONE-DIGIT BINARY DIGIT (0 OR 1) INDICATING THE STATE OF THE
TRANSMITTER'S AUTO-RESTORE SWITCH (0 = OFF, 1 = ON).
GROUND
AN 18-FOOT RG-58 CABLE IS SUPPLIED WITH THE
ANT-2 KIT. UP TO 50 FEET OF RG-58 CAN BE USED.
USE RG-8 FOR UP TO 100-FOOT CABLE RUNS.
V = TRANSMITTER VOLTAGE CHARACTER (H OR L). NORMAL CONDITION = "H". IF
TRANSMITTER VOLTAGE IS BELOW 10.5 VDC CHARACTER = "L".
XR-D TO MALE DB-25 FOR PRINTER CABLE
SIG GND
DTR
PIN 7 (SIG GND)
PIN 6 (DSR)
PIN 3 (RD)
MALE
DB-25
X = SPARE CHARACTER, NOT IMPLEMENTED AT THIS TIME.
TD
+
12 VDC
E = END-OF-DATA. A CARRIAGE RETURN AND A LINE FEED ARE SENT.
GROUND
TO UNIT
9
. TEST SYSTEM
TRANSMITTER
10. COMPLETE INSTALLATION
LINEAR LIMITED WARRANTY
This Linear product is warranted against defects in material and workmanship
for twelve (12) months. The Warranty Expiration Date is labeled on the product.
This warranty extends only to wholesale customers who buy direct from Linear or
through Linear’s normal distribution channels. Linear does not warrant this product
to consumers. Consumers should inquire from their selling dealer as to the nature of
the dealer’s warranty, if any. There are no obligations or liabilities on the part of
Linear LLC for consequential damages arising out of or in connection with use
or performance of this product or other indirect damages with respect to loss of
property, revenue, or profit, or cost of removal, installation, or reinstallation. All
implied warranties, including implied warranties for merchantability and implied
warranties for fitness, are valid only until Warranty Expiration Date as labeled on the
product. This Linear LLC Warranty is in lieu of all other warranties express or
implied.
INSTALL AND SETUP THE TRANSMITTER AS
DESCRIBED IN ITS INSTALLATION INSTRUCTIONS
APPLY POWER AND TRIGGER THE
TRANSMITTER'S INPUT
1
SECURE END PLATE BY
INSTALLING THE FOUR
CASE SCREWS
INSTALL THE TWO REMAINING
MOUNTING SCREWS
THE TRANSMIT INDICATOR
SHOULD LIGHT WHEN THE
TRANSMITTER IS TRIGGERED
2
SLIDE RECEIVER
BOARD INTO CASE IN
THE 3RD SLOT UP
WARNING
All products returned for warranty service require a Return Product Authorization
Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA#
and other important details.
NEVER CONNECT THE TRANSMITTER AND
RECEIVER ANTENNA CONNECTORS
DIRECTLY TO EACH OTHER. MAJOR
DAMAGE TO BOTH UNITS WILL OCCUR!
VERIFY THAT COMPUTER OR PRINTER
IS SETUP PROPERLY AND ACQUIRING
THE DATA FROM THE RECEIVER
IMPORTANT !!!
(
BUTTON WILL ALSO SEND DATA)
PRESSING THE RECEIVER'S TEST
Linear radio controls provide a reliable communications link and fill an important need
in portable wireless signaling. However, there are some limitations which must be
observed.
RECEIVER
1
WARNING: THIS PRODUCT IS NOT TO BE USED IN LIFE SAFETY APPLICATIONS. FCC Rules allow
unlicensed high-power transmissions at or near the operating frequency of this product which may
interfere with, or even disable, normal operation of this radio device.
3
BAUD RATE: 9600
STOP BITS: 1
PARITY: NONE
1
1
For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 95
Radio Control devices. As such, they have limited transmitter power and therefore limited range.
A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals
that occur on or near their operating frequencies, regardless of code settings.
Changes or modifications to the device may void FCC compliance and user’s authority to operate equipment.
Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
TIGHTEN WIRING STRAIN
RELIEF BUSHING TO
SECURE AND WEATHER
PROOF WIRING
1
1
SEND MORE TEST TRANSMISSIONS, THE
RECEIVER'S SIGNAL INDICATOR SHOULD
LIGHT AS THE SIGNALS ARE RECEIVED (IF
LIT WITH NO SIGNALS, IT IS INTERFERENCE)
TEST SYSTEM AGAIN AFTER
COMPLETING INSTALLATION
1 A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or
dealer, and these facts should be communicated to the ultimate users.
Copyright © 2004 Linear LLC
215170 B
In addition to the user manual Linear XR-D, we also provide a support panel to help you solve your problems with Linear XR-D. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Linear XR-D. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Linear XR-D - you will surely help many users by doing so.
Have you got problems with your device? Ask a question - our users can help you