User manual RCA 32F650T

If you found this page, you probably have a problem and you need a user manual for the device RCA 32F650T. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database RCA 32F650T it belongs to the category Satellite TV System. A user manualRCA 32F650T is taken from the manufacturer, a RCA company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device RCA 32F650T directly. You can view the user manualRCA 32F650T directly online or save and store it on your computer.

Using the Remote Control  
Using Automatic Code Search  
The following instructions can be used to program the remote to operate each of  
your components. If you want to stop the automatic code search without  
programming any of your components, press CLEAR until the indicator on the  
remote turns off.  
1
2
. Turn on the component you want to operate (VCR, DVD player, etc.)  
. Press and hold the component button you want to program (VCR, DVD, etc.).  
While holding the component button, press and hold ON•OFF until the  
indicator on the remote turns on, then release both buttons.  
3
. Point the remote at the component. Press and release PLAY (the indicator light  
on the remote flashes).  
The remote is searching for the correct code to program. When the indicator  
stops flashing (after about 5 seconds), press PLAY again to tell the remote to  
search the next set of codes.  
Continue pressing PLAY until the component turns off or the indicator light on  
the remote turns off. If the indicator light turns off, then all the codes for that  
particular component have been tested once. If the component does not turn  
off, then the remote can’t be programmed to operate that component.  
Note: Each time you press PLAY, the remote sends about 10 sets of codes. Therefore, you  
might have to press the PLAY button up to 20 times.  
If the component you want to control does turn off:  
1
. Press and release REVERSE, then wait 2 seconds. Repeat this step until the  
component turns back ON.  
2
. To finish, press and hold STOP until the indicator on the remote turns off.  
Using Direct Entry  
1
2
. Turn on the component to be programmed.  
. Look up the brand and code number(s) for the component on the code list in  
this section.  
3
4
. Press and hold the component button you want to program on the remote.  
. Enter the 4-digit code from the remote control code list on the following  
pages. If the indicator flashes, you have either entered an invalid code or the  
button isn’t programmable.  
5
6
. Release the component button.  
. Point the remote at the component. Press ON•OFF to see if the component  
responds to the command. If it doesn’t, try pressing the component button and  
then ON•OFF again.  
If you get no response, repeat these steps using the next code listed for your  
brand, until the component responds to the remote commands.  
If you try all the codes for your component brand and none work, try the  
automatic code search method. If automatic code search doesn’t find the code,  
the remote is not compatible with your component.  
Chapter 2  
Graphics contained within this publication are for representation only.  
11  
1616302A.02_Remote  
11  
4/15/04, 10:17 PM  

In addition to the user manual RCA 32F650T, we also provide a support panel to help you solve your problems with RCA 32F650T. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with RCA 32F650T. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with RCA 32F650T - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.