User manual Bosch Power Tools GTS1031

If you found this page, you probably have a problem and you need a user manual for the device Bosch Power Tools GTS1031. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Bosch Power Tools GTS1031 it belongs to the category Saw. A user manualBosch Power Tools GTS1031 is taken from the manufacturer, a Bosch Power Tools company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Bosch Power Tools GTS1031 directly. You can view the user manualBosch Power Tools GTS1031 directly online or save and store it on your computer.

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 15  
CHANgINgTHEbꢀAdE  
NOTE: Clean blade of any excess oil before  
installation.  
ATTACHINgRIpꢂENCEꢂORUSE  
FIG. 12  
2
1. Remove the table insert 1 (Fig. 11).  
5
2. Raise the blade 2 to the maximum height by turn-  
ing the control wheel 3 counterclockwise (Fig. 11).  
3. Remove the arbor nut 4 and flange 5 (Fig. 12).  
4
. To loosen the arbor nut 4, use the open-end  
wrench 7 and align the wrench jaws on the flats  
of the flange to keep the arbor from turning. Place  
the box-end wrench 8 on the arbor nut 4 and turn  
counter-clockwise (to the front of the saw table)  
4
(Fig. 13).  
6
5
. Clean any sawdust from both blade collars before  
installing the blade. Install a 10" (25.4 cm) blade.  
Install the saw blade onto the arbor with the blade  
teeth pointing toward the front of the saw.  
ANdSTORAgE  
. Raise rip fence handle 1, so holding clamp 2 is  
out far enough to fit on the table 3 and into “V”  
1
FIG. 13  
To avoid injury, do not use a blade larger or smaller  
than 10" diameter and 5/8" arbor.  
6
. Install the flange 5 against the blade 2 and thread  
the arbor nut 4 as far as possible by hand. Ensure  
that the blade is flush against the inner blade  
flange 6 (Fig. 12).  
7
7
. To tighten the arbor nut 4, use the open-end  
wrench 7 and align the wrench jaws on the flats  
of the flange to keep the arbor from turning. Place  
the box-end wrench 8 on the arbor nut 4 and turn  
clockwise (to the rear of the saw table) (Fig. 13).  
8
8
. Install the table insert 1 in the table recess.  
(Figure 11).  
To avoid injury from a thrown workpiece, blade part,  
or blade contact, never operate the saw without the  
proper insert in place. Use the table insert when  
sawing. Use the dado insert when using a dado  
blade.  
4
USINgCARbIdE-TIppEdbꢀAdES  
Handle carbide-tipped blades carefully. Carbide is  
very brittle and can be easily damaged. Use caution  
when you install, use or store the blades. Do not use  
a carbide-tipped blade that is bent or has bent teeth,  
or if the blade has cracks, is broken, or has  
missing/loose carbide tips. Do not operate a carbide-  
tipped blade faster than its recommended speed.  
groove located on the back of rear rail (Fig. 14).  
2
. Position the rip fence 4 over table 3 holding up the  
front end, first engage holding clamp 2 with rear  
rail.  
3
. Lower front end onto front rail 5.  
Read, understand and follow all warnings and in-  
structions provided with your carbide-tipped 4. Lower rip fence handle to lock.  
blades.  
Note: To store rip fence follow same procedure as  
above under the table (Fig. 15).  
-15-  

In addition to the user manual Bosch Power Tools GTS1031, we also provide a support panel to help you solve your problems with Bosch Power Tools GTS1031. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Bosch Power Tools GTS1031. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Bosch Power Tools GTS1031 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.