User manual Bosch Power Tools GTS1031

If you found this page, you probably have a problem and you need a user manual for the device Bosch Power Tools GTS1031. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Bosch Power Tools GTS1031 it belongs to the category Saw. A user manualBosch Power Tools GTS1031 is taken from the manufacturer, a Bosch Power Tools company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Bosch Power Tools GTS1031 directly. You can view the user manualBosch Power Tools GTS1031 directly online or save and store it on your computer.

BM 2610014415 01-11 E:BM 2610012089 12-10 E 1/10/11 7:17 AM Page 3  
AꢄꢄitionalSafetyRules  
dIRECTIONOꢂꢂEEd  
7.STAbIꢀITꢁOꢂSAW  
Feed work into a blade or cutter against the direction Your table saw MUST BE BOLTED securely to a  
of rotation of the blade or cutter only.  
stand or workbench. In addition, if there is any ten-  
dency for the table saw to tip over or move during  
certain operations such as cutting long, heavy  
boards, use an auxiliary support.  
NEVERꢀEAVETOOꢀRUNNINgUNATTENdEd  
Turn power off. Don’t leave tool until it comes to a  
complete stop.  
8
.ꢀOCATION  
ToolCare  
dONOTAꢀTERORMISUSETOOꢀ  
These tools are precision built. Any alteration or  
modification not specified is misuse and may result  
in dangerous conditions.  
Use the table saw in a well lit area and on a level  
surface, clean and smooth enough to reduce the risk  
of trips and falls. Use it where neither the operator  
nor the casual observer is forced to stand in line with  
the blade.  
AVOIdgASEOUSAREAS  
9.KICKbACK  
Do not operate electric tools in gaseous or explosive  
atmospheres. Motors in these tools normally spark,  
and may result in a dangerous condition.  
Kickbacks can cause serious injury: A “KICKBACK”  
occurs when a part of the workpiece binds between  
the sawblade and the rip fence or other fixed object.  
Workpiece binding the blade due to misalignment,  
MAINTAINTOOꢀSWITHCARE  
Keep tools sharp and clean for better and safer can also cause kickback. During kickback, work-  
performance. Follow instructions for lubricating and piece rises from table and is thrown toward the op-  
changing accessories. Inspect tool cords periodi- erator. Keep your face and body to one side of the  
cally and if damaged, have repaired by authorized sawblade, out of line with a possible “KICKBACK”.  
service facility. Inspect extension cords periodically  
and replace if damaged. Keep handles dry, clean  
and free from oil and grease.  
KICKbACKSANdpOSSIbꢀEINjURꢁCAN  
USUAꢀꢀꢁbEAVOIdEdbꢁ:  
a. Maintaining the rip fence parallel to the sawblade.  
Before connecting the tool to a  
WARNING  
power source (receptacle, outlet,  
ꢃ. Keeping the sawblade sharp. Replacing or sharp-  
ening anti-kickback pawls when points become dull.  
!
etc.), be sure voltage supplied is the same as that  
specified on the nameplate of the tool. A power  
source with voltage greater than that specified for  
the tool can result in serious injury to the user — as  
well as damage to the tool. If in doubt, DO NOT  
PLUG IN THE TOOL. Using a power source with  
voltage less than the nameplate rating is harmful to  
the motor.  
c. Keeping sawblade guard, spreader and anti-kick-  
back pawls in place and operating properly. The  
spreader must be in alignment with the sawblade  
and the pawls must stop a kickback once it has  
started. Check their action before ripping.  
ꢄ. NOT ripping workpiece that is twisted or warped  
or does not have a straight edge to guide along the  
rip fence.  
For your own safety, do not operate  
WARNING  
your table saw until it is completely  
assembled and installed according to the instruc-  
tions … and until you have read and understood the  
following:  
!
e. NOT releasing work until you have pushed it all  
the way past the sawblade.  
f. Using a Push Stick for ripping widths of 2" to 6"  
and an auxiliary fence and Push Block for ripping  
widths narrower than 2" (See “Basic Saw Operation,  
Using The Rip Fence” section, pages 29, 30).  
1
2
3
4
5
6
7
. General Safety Rules. . . . . . . . . . . . . . . . . . 2–5  
. Double Insulated Tools . . . . . . . . . . . . . . . . . . . 6  
. Getting To Know Your Table Saw. . . . . . . . 9, 10  
. Assembly . . . . . . . . . . . . . . . . . . . . . . . . . 12–16  
. Adjustments . . . . . . . . . . . . . . . . . . . . . . . 17–21  
. Basic Table Saw Operation . . . . . . . . . . . 22–34  
. Maintaining Your Table Saw. . . . . . . . . . . 34–35  
ꢅ. NOT confining the cut-off piece when ripping or  
crosscutting.  
h. When ripping, apply the feed force to the section  
of the workpiece between the sawblade and the rip  
fence. Use Push Stick or Push Block when appro-  
priate (See item f. above).  
SAVTEHESINESTRUCTIONS”  
-3-  

In addition to the user manual Bosch Power Tools GTS1031, we also provide a support panel to help you solve your problems with Bosch Power Tools GTS1031. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Bosch Power Tools GTS1031. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Bosch Power Tools GTS1031 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.