User manual Panasonic 999000

If you found this page, you probably have a problem and you need a user manual for the device Panasonic 999000. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Panasonic 999000 it belongs to the category Saw. A user manualPanasonic 999000 is taken from the manufacturer, a Panasonic company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Panasonic 999000 directly. You can view the user manualPanasonic 999000 directly online or save and store it on your computer.

After the saw works for a certain period of time, let the engine idle on for a while to dissipate the  
heat. This will prevent some engine parts (ignition system, carburetor, etc.) from being damaged  
by over heating.  
ADJUSTMENT OF CUTOFF SAW  
1
. Adjusting V-belt tension:  
Refer to the instruction described above in the section titled “Tensioning the V-belt.”  
2
. Adjusting carburetor:  
The carburetor has been preset and adjusted at the factory to reach the optimum fuel-air mixture  
for a smooth, fuel efficient, reliable running engine with low emissions. The air  
filter and the spark plug need to be checked and maintained regularly. However, if the cutoff saw  
is found to be unsatisfactory in operation (such as the idle speed either too high or too low, or  
abnormal exhaust emission still persist), a slight adjustment on the carburetor might be necessary,  
which includes (Ref. Fig. 9):  
Standard setting adjustment:  
Find the Low Speed Adjusting Screw “L” (see Fig.9, inside  
the upper hole of the carburetor seal cover), use a screw  
driver to turn the screw L clockwise all the way to its end.  
Then turn the screw L backwards (counterclockwise) 360°.  
Adjusting idling speed:  
It is usually necessary to adjust the idle speed after Standard  
setting adjustment (above). To adjust idle speed, start the  
engine first.  
If the idle speed is too low, the engine may shut off after  
starting. In this case, make the standard setting first as  
instructed [above], then turn the idle speed adjusting screw LA  
(
see Fig. 9) inside the lower hole of carburetor seal cover  
clockwise until the blade starts to run. Then turn the screw LA  
backwards (counterclockwise)  
Fig. 9  
1
/4 circle (90°).  
If the idling speed is too high, the blade will run at idling speed, which is not good for the cutoff  
saw. In this case, make standard setting adjustment first, then turn the idling speed adjusting  
screw LA counterclockwise until the blade stops running. Then turn the screw  
LA 90°further (counterclockwise).  
3
. Adjusting blade guard (Ref. Fig.10):  
The blade guard deflects sparks from the operator. Move the adjusting  
lever (2) to change the position of the blade guard.  
MAINTENANCE & REPAIR OF THE CUTOFF SAW  
1
. Cleaning and maintenance of the air filter  
Dust and foreign build-up accumulated on the air filter may affect  
engine performance, increase fuel consumption and cause difficulty in  
starting; therefore, it is important to perform regular maintenance. The  
frequency of this depends on the conditions of the cutting jobs as well as  
Fig. 10  
material being cut both wet or dry. For dry cutting, maintenance is required every 48 hours. For  
instructions, see Fig. 11.  
1
3

In addition to the user manual Panasonic 999000, we also provide a support panel to help you solve your problems with Panasonic 999000. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Panasonic 999000. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Panasonic 999000 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.