If you found this page, you probably have a problem and you need a user manual for the device Wilton PF3-EZ. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Wilton PF3-EZ it belongs to the category Saw. A user manualWilton PF3-EZ is taken from the manufacturer, a Wilton company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Wilton PF3-EZ directly. You can view the user manualWilton PF3-EZ directly online or save and store it on your computer.

Recommended Gauges (AWG) of Extension Cords  

Extension Cord Length *  

Extension Cords  

If an extension cord is necessary make sure the  

cord rating is suitable for the amperage listed on  

the machine's motor plate. An undersize cord  

will cause a drop in line voltage resulting in loss  

of power and overheating.  

25 100 150 200  

50  

75  

Amps  

feet feet feet feet feet feet  

<

5

16  

16  

14  

12  

10  

10  

16  

16  

14  

12  

10  

NR  

16  

14  

12  

10  

10  

NR  

14  

12  

12  

10  

12  

5

to 8  

NR  

NR  

NR  

NR  

NR  

The chart in Figure 7 shows the correct size  

cord to use based on cord length and motor  

plate amp rating. If in doubt, use the next  

heavier gauge. The smaller the gauge number  

the heavier the cord.  

8

to 12  

10  

NR  

NR  

NR  

NR  

12 to 15  

10  

1

5 to 20  

1 to 30  

NR  

NR  

2

*

based on limiting the line voltage drop to 5V at 150% of the  

Adjustments  

rated amperes.  

NR: Not Recommended.  

Swing  

Figure 7  

To swing the Stock Feeder laterally, loosen the  

cam handle counterclockwise so that it pushes  

down the pin, as shown in Figure 8. Swing the  

horizontal arm and feeder into desired position  

(

the top part of the stand will rotate). When the  

Stock Feeder is properly positioned, tighten cam  

handle.  

To rotate the top of the stand back to original  

position, loosen the cam handle and rotate the  

top section of the stand, allowing the pin to snap  

back into the hole. Tighten the cam handle.  

Raise/Lower  

Figure 8  

To raise or lower the Stock Feeder, loosen the  

handle (A, Figure 9) and rotate the elevating  

handle (B, Figure 9). When finished, tighten the  

handle (A, Figure 9).  

Forward/Back  

To move the horizontal arm forward or back,  

loosen the handle (C, Figure 9) and rotate the  

handwheel (D, Figure 9). When finished, tighten  

the handle (C, Figure 9).  

Figure 9  

Rotate  

To rotate the Stock Feeder (up to 360 degrees),  

loosen the handle on the vertical arm (A, Figure  

9

). When finished rotating the Stock Feeder,  

tighten the handle (A, Figure 9).  

12  

• ← Previous
• Next page →

In addition to the user manual Wilton PF3-EZ, we also provide a support panel to help you solve your problems with Wilton PF3-EZ. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Wilton PF3-EZ. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Wilton PF3-EZ - you will surely help many users by doing so.