User manual Skil 1677M

If you found this page, you probably have a problem and you need a user manual for the device Skil 1677M. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Skil 1677M it belongs to the category Saw. A user manualSkil 1677M is taken from the manufacturer, a Skil company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Skil 1677M directly. You can view the user manualSkil 1677M directly online or save and store it on your computer.

BM 1619X01743 08-06 8/17/06 8:48 AM Page 9  
Operating Instructions  
DEPTH ADJUSTMENT  
DEPTH ADJUSTMENT  
LEVER  
FIG. 3  
Disconnect plug from power source. Loosen  
the depth adjustment lever located between  
the guard and handle of saw. Hold the foot  
down with one hand and raise or lower saw by  
the handle. Tighten lever at the depth setting  
desired. Check desired depth (Fig. 3).  
Not more than one tooth length of the blade  
should extend below the material to be cut, for  
minimum splintering (Fig. 3).  
ONE TOOTH LENGTH SHOULD  
PENETRATE WOOD FOR  
MINIMUM SPLINTERING  
QUADRANT  
90° CUTTING ANGLE CHECK  
FIG. 4  
Disconnect plug from power source. Set foot to  
maximum depth of cut setting. Loosen bevel  
adjustment lever, set to 0° on quadrant,  
retighten bevel adjustment lever first, then the  
depth adjustment lever and check for 90°  
angle between the blade and bottom plane of  
foot with a square (Fig. 4). Make adjustments  
by turning the small alignment screw from  
bottom side of foot, if necessary (Fig. 4).  
BEVEL  
ADJUSTMENT  
LEVER  
0
°
FOOT  
90°  
BLADE  
ALIGNMENT  
SCREW  
BEVEL ADJUSTMENT  
may occur. Keep the saw steady and the foot  
Disconnect plug from power source. The foot firmly on the workpiece.  
can be adjusted up to 45° by loosening the  
4
5° STOP  
BEVEL  
ADJUSTMENT  
LEVER  
bevel adjustment lever at the front of the saw  
and aligning foot to desired angle on  
calibrated quadrant. To maintain adjustment,  
Always tighten bevel adjustment first, then  
the depth adjustment lever (Fig. 5).  
SPRING  
FIG. 5  
For 50° cuts, loosen bevel adjustment lever,  
depress 45° stop spring, adjust foot to 50° and  
tighten lever (Fig. 5). Because of the increased  
amount of blade engagement in the work and  
decreased stability of the foot, blade binding  
QUADRANT  
LINE GUIDE  
9
0° VERTICAL CUTS  
FIG. 6  
For a straight 90° cut, use the large notch in  
the foot. For 45° bevel cuts, use the small  
notch (Fig. 6). The cutting guide notch will  
give an approximate line of cut. Make sample  
cuts in scrap lumber to verify actual line of cut.  
This will be helpful because of the number of  
different blade types and thicknesses  
available. To ensure minimum splintering on  
the good side of the material to be cut, face  
the good side down.  
FOOT  
4
5° / 50° BEVEL CUTS  
PUSH  
45°STOP  
SPRING IN  
DIRECTION  
OF ARROW  
FOR 50°  
BEVEL  
ADJUSTMENT  
-
9-  

In addition to the user manual Skil 1677M, we also provide a support panel to help you solve your problems with Skil 1677M. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Skil 1677M. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Skil 1677M - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.