User manual JBL LSR6328P

If you found this page, you probably have a problem and you need a user manual for the device JBL LSR6328P. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database JBL LSR6328P it belongs to the category Speaker System. A user manualJBL LSR6328P is taken from the manufacturer, a JBL company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device JBL LSR6328P directly. You can view the user manualJBL LSR6328P directly online or save and store it on your computer.

Amplitude & Phase  
SSyspteme: cifications:  
Frequency Response (+1, -1.5 dB): 50 Hz - 20 kHz  
Enclosure Resonance Frequency: 38 Hz  
Low Frequency Extension: User controls set to default  
-
3 dB: 46 Hz  
-
10 dB: 36 Hz  
Low-High Frequency Crossover: 1.7 kHz 6th-order acoustic Linkwitz-Riley  
Distortion, 96 dB SPL, 1 m:  
Mid-High Frequency (120 Hz - 20 kHz):  
2
nd Harmonic: <0.6%  
rd Harmonic: <0.5%  
Low Frequency (<120 Hz):  
nd Harmonic: <2%  
rd Harmonic: <1%  
3
2
3
Maximum SPL (80 Hz - 20 kHz): >108 dB SPL / 1m  
Maximum Peak SPL (80 Hz - 20 kHz): >111 dB SPL / 1m  
Signal Input: Neutrik “Combi” XLR-¼-in tip-ring-sleeve balanced or unbal-  
96 dB/1 m (Distortion raised 20 dB)  
anced positive voltage applied to XLR pin 2 (¼" tip) produces  
outward woofer motion  
Calibrated Input Sensitivity, XLR & ¼":  
4 dBu / +8 dBu: 96 dB SPL / 1 m  
10 dBV: 96 dB SPL / 1 m  
+
-
AC Input Voltage: 100 /240 VAC, 50/60 Hz (auto sensing)  
AC Input Connector: IEC  
Long-Term Maximum System Power: 220 watts (IEC265-8)  
Self-Generated Noise Level: <10 dBA / 1 m Tonal-artifact-free noise floor  
User Controls:  
2
nd  
rd  
3
High Frequency Control (2 kHz - 20 kHz): +1 dB, 0 dB, -1 dB  
Low Frequency Control (< 100 Hz): 0 dB, -2 dB  
Low Frequency Alignments: 36 dB/octave, 24 dB/octave (VLF protection off)  
Calibrated Input Sensitivity: -10 dBV, +4 dBu, +8 dBu  
Boundary Compensation Settings: 0, -1.5, -3.0, -4.5 dB  
Variable Input Attenuation: 0 dB to -13 dB  
RMC External Bypass: ¼" jack  
RMC Active Switch: In/Out  
RMC Frequency Adjust: 26 Hz - 96 Hz (10th octave, 18 centers)  
RMC Depth Adjust: 0 - 14 dB (cut only)  
102 dB/1 m (Distortion raised 20 dB)  
RMC Q Adjust: 1/20th to 1/2 octave, 21 steps  
Transducers:  
Low Frequency Model: 218F  
Diameter: 203 mm (8 in)  
®
Voice Coil: 38 mm (1.5 in) Differential Drive with dynamic braking coil  
Magnet Type: Ferrite, with integral heat sink  
Cone Type: Carbon fiber composite  
2nd  
Impedance: 2 ohms  
High Frequency Model: 053TiS  
Diameter: 25 mm (1 in) diaphragm  
Voice Coil: 25 mm (1 in)  
3rd  
Magnet Type: Ferrite, shielded  
Diaphragm Type: Damped titanium composite  
Other Features: Elliptical oblate spheroidal waveguide  
Impedance: 4 ohms  
Amplifier:  
Low Frequency:  
Topology: Class A-B, all discrete  
Notes:  
Sine Wave Power Rating: 250 watts (<0.1% THD into rated impedance)  
THD + N, ½Power: <0.05%  
All measurements unless otherwise stated made anechoically in a 4environment at 2  
meters, referenced to 1 meter by inverse square law.  
High Frequency:  
The reference measurement microphone position is located perpendicular to the cen-  
terline of the low and high frequency transducers at the point 55 mm (2.2 in) below  
the center of the high frequency diaphragm.  
Acoustic loading provided by the listening room increases maximum SPL capability  
and low frequency bass extension as compared to stated anechoic values.  
Topology: Class A-B, monolithic  
Sine Wave Power Rating: 120 watts (<0.1% THD into rated impedance)  
THD + N, ½Power: <0.05%  
Physical:  
Distortion measurements performed with the input voltage necessary to produce the  
stated A- weighted SPL at the stated measurement distance. Distortion figures refer to  
the maximum distortion measured in any 1/10th octave wide band in the stated fre-  
quency range.  
Finish: Smooth dark graphite  
Handles: 2 each, flush mounted on sides  
Mounting: 4 threaded mounting points conforming to industry standard  
square pattern, 127 x 70 mm (5 x 2.75 in) center to center. M6  
metric threads.  
Enclosure Volume (net): 28 liter (1 cu ft)  
Low Frequency Vent: Rear ported linear dynamics aperture (integrated with  
amplifier heat sink)  
JBL continually engages in research related to performance improvements. New mate-  
rials, production methods, and design refinements are introduced into existing prod-  
ucts without notice as a routine expression of that philosophy. For this reason, any  
current JBL product may differ in some respect from its published description, but will  
always equal or exceed the original design specification unless otherwise stated.  
Baffle Construction: Injection-molded structural ABS  
Enclosure Construction: 19 mm (¼in) MDF  
Net Weight: 17.7 kg (39 lb)  
Dimensions (HxWxD): 406 x 330 x 325 mm (16 x 13 x 12.8 in)  
Caution: Unsafe mounting or overhead suspension of any heavy load can result in serious injury and equipment  
damage. Mounting of speakers should be done by qualified persons in accordance with all applicable local safety  
and construction standards. Be certain to follow the instructions provided by the manufacturer of the mounting  
bracket. Before selecting a mounting bracket, be certain that it is capable of supporting the weight of the speaker  
to be mounted.  

In addition to the user manual JBL LSR6328P, we also provide a support panel to help you solve your problems with JBL LSR6328P. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with JBL LSR6328P. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with JBL LSR6328P - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.