User manual JVC SP-XF10S

If you found this page, you probably have a problem and you need a user manual for the device JVC SP-XF10S. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database JVC SP-XF10S it belongs to the category Speaker System. A user manualJVC SP-XF10S is taken from the manufacturer, a JVC company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device JVC SP-XF10S directly. You can view the user manualJVC SP-XF10S directly online or save and store it on your computer.

Thank you for purchasing JVC speakers.  
Before you begin using them, please read the instructions carefully.  
English  
Speaker units  
Connections  
1
Speaker cord  
Front speaker (2)  
Center speaker (1)  
Surround speaker (2)  
Connect the speaker cords to the speaker terminals.  
2
Precautions for installation and daily use  
Press  
Insert  
Release  
Be sure to have the speakers installed on the wall by a qualified  
personnel to avoid unexpected damage from falling off the wall due to  
incorrect installation or weakness in the wall structure.  
Red (+)  
Care must be taken in selecting the location of installation on the wall.  
Injuries or damages may result if the speakers installed interfere with  
daily activities.  
Black ()  
The speakers are magnetically shielded to avoid color distortions on  
TVs if they are installed properly.  
SP-XF20C  
Rear)  
(
Copper  
Black striped  
When placing the speakers near a TV set, turn off the TVs main  
power switch or unplug it before installing the speakers.  
Then wait at least 30 minutes before turning on the TVs main power  
switch again. If there are still distortion, move the speakers further  
away from the TV.  
SP-XF20F  
(Rear)  
Press  
Red (+)  
Do not reproduce sounds at so high a volume that they are distorted;  
otherwise, the speakers may be damaged by internal heat buildup.  
When moving the speakers, do not pull the speaker cords; otherwise,  
the speakers may fall over, causing damage or injury.  
Black ()  
Connecting the speaker system to the amplifier  
Before connecting—  
Insert  
Turn off the power to the amplifier before connecting the speaker  
system; otherwise, the speakers may be damaged.  
Black striped  
The impedance of each speaker is 6 . Before connecting them to your  
amplifier, check the speaker impedance range of your amplifier. If the  
impedance of this speaker is out of the speaker impedance range  
indicated on the amplifier, you cannot connect this system to the amplifier.  
The maximum power handling capacity of the speakers are 100 W.  
Excessive input will result in abnormal noise and possible damage.  
Be sure to turn down the volume level to prevent unwanted noise  
before performing following operations:  
Copper  
Release  
SP-XF10S  
(Bottom)  
Turning on or off other components,  
Operating the amplifier,  
Tuning FM stations,  
Fast-forwarding a tape,  
Continuously reproducing high frequency oscillation or high pitch  
electronic sounds,  
Black striped  
Copper  
Through the hole  
Connecting or disconnecting a microphone.  
Connecting the speakers to the amplifier.  
When using a microphone, do not aim it at the speakers or use it near  
the speakers; otherwise, the howling which occurs may damage the  
speakers.  
Before replacing the cartridge, always turn off the power to the  
turntable; otherwise, the clicking noise may damage the speakers.  
3
Front left  
Front right  
Center  
Amplifier  
Subwoofer  
Specifications  
Type (magnetically-shielded type):  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
2-way 3-speaker Bass-reflex type  
1-way Bass-reflex type  
Speaker units:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
Power handling capacity/Impedance: 100 W/6 Ω  
Frequency range:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
Sound pressure level:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
Dimensions (W ×H ×D): SP-XF20F: 84 mm ×211 mm ×88 mm  
SP-XF20C: 209 mm ×85 mm ×92 mm  
Surround left  
Surround right  
5.5 cm cone (×2), 3.0 cm dome  
8.0 cm cone  
Connect the speakers to the speaker terminals of the amplifier  
with the speaker cords by referring to the diagram below.  
Make sure to match the polarity (ªand ·) when connecting  
the speaker cords.  
90 Hz to 40 000 Hz  
80 Hz to 20 000 Hz  
The diagram below is an example of a typical connection.  
FRONT LEFT  
CENTER  
81 dB/Wm  
75 dB/Wm  
FRONT RIGHT  
FRONT CENTER SURROUND SURROUND  
BACK  
SPEAKERS  
RIGHT LEFT  
RIGHT  
LEFT  
Recommended to use  
SP-SB100 (optionally  
purchased).  
SP-XF10S: 111.5 mm ×139 mm ×106.5 mm  
0.87 kg each  
0.52 kg each  
4 m (×3); 10 m (×2)  
Mass:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
SURROUND RIGHT  
SURROUND LEFT  
Accessories: Speaker cords:  
Design and specifications are subject to change without notice.  
3 –  
EN02-03_SP-XF20[E]f.p65  
3
31/3/04, 12:54 PM  

In addition to the user manual JVC SP-XF10S, we also provide a support panel to help you solve your problems with JVC SP-XF10S. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with JVC SP-XF10S. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with JVC SP-XF10S - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.