User manual Ashly ne 8250.70

If you found this page, you probably have a problem and you need a user manual for the device Ashly ne 8250.70. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Ashly ne 8250.70 it belongs to the category Stereo Amplifier. A user manualAshly ne 8250.70 is taken from the manufacturer, a Ashly company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Ashly ne 8250.70 directly. You can view the user manualAshly ne 8250.70 directly online or save and store it on your computer.

Operating Manual - NE Multi Channel Power Amplifiers  
Amplifier Rear Panel  
1
. Optional Cobranet Card CNM-2 Installation of this option allows this amplifier to be part of a Cobranet  
audio network.  
2
3
4
. Optional AES/EBU Input or MIC Input - Installation of this option allows for AES/EBU or MIC inputs.  
. Ethernet Port - This offers ethernet control and monitoring of amplifier functions using Proteane software.  
. Input Connector - This is used for a three wire (G, +, -) balanced input, and uses two-piece  
euroblock connectors.  
5
6
7
8
. Normal/Bridge Switch - This switches the channel pair to Bridge Mode  
. Euroblock Speaker Connectors - Used to connect the speakers  
. Remote Standby - These two contact closure pins are wired to a switch to remotely place the amp in standby.  
. Preset Recall - These four pins (and GND) can be wired to remote contact closure switches to recall up to four  
amplifier presets.  
9
1
. Data - These four pins can be wired to remote microprocessor based controllers such as the WR-5 or RD-8C.  
0. Remote Level Control - These pins can be wired to remote potentiometers such as the WR-1 for level control  
of individual channels  
1
1. AC Inlet - Used for the detachable AC cord.  
WARNING: Do not remove or lift the mains connector ground.  
Installation  
Before connecting to mains power, make sure that the switches and wiring are all set to the configuration needed  
for your particular application. Failure to do so could result in damage to the unit or other components in your system.  
CAUTION: When mounting or connecting the amplifier, always disconnect it from the mains. Use four screws and  
washers when mounting the amplifier to the front rack rails. Rear support is also recommended, especially for mobile or  
touring use. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.  
Requirements  
NE-series multichannel amplifiers have specific physical, electrical and signal requirements for proper operation.  
These requirements will vary de pending on your specific application, setup, and the settings on the amplifier. When  
setting up and testing your system, please take special care to double check all connections and settings. Please refer to  
the specifications section of this manual for specific input, output and other figures.  
Constant Voltage Models (25V, 70V, and 100V) and High Pass Filters  
The 25V, 70V, and 100V amplifiers include internal, factory installed High Pass Filter hardware. This allows for  
software selectable filters on each channel that prevent low frequency energy from saturating the core of low cost  
speaker tap transformers. Available settings are 80Hz (12dB/oct), 400Hz (6dB/oct), and OFF. The 400Hz setting is  
commonly used in paging systems with horn speakers. Note that with the HPF hardware installed, that amplifier can  
not have any of the optional AES/EBU input, MIC input, or DSP hardware.  
The DSP option can be factory installed in lieu of the HPF hardware, with HPF frequencies set in software to any  
value from 20Hz to 20kHz with a slope of 12dB/oct to 48dB/oct and various response options. In order to have AES/  
EBU capability in a constant voltage amplifier, the DSP option must be installed.  
7

In addition to the user manual Ashly ne 8250.70, we also provide a support panel to help you solve your problems with Ashly ne 8250.70. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Ashly ne 8250.70. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Ashly ne 8250.70 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.