If you found this page, you probably have a problem and you need a user manual for the device Extron electronic XPA 1002. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Extron electronic XPA 1002 it belongs to the category Stereo Amplifier. A user manualExtron electronic XPA 1002 is taken from the manufacturer, a Extron electronic company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Extron electronic XPA 1002 directly. You can view the user manualExtron electronic XPA 1002 directly online or save and store it on your computer.

Installation, cont’d  

Lift Cover Straight Up  

10. Connect the black hot (line) and white neutral wires to  

the terminal block on the PCB using the 2 screws that  

were removed in step . Use the included zip tie wrap to  

secure the two wires together close to the terminals. See  

the following illustration.  

Remove (8)  

screws  

W

Ensure that you observe correct wire polarity. The  

following illustration shows the location of the hot  

(

L) and neutral (N) terminals.  

XPA 1002  

WIRING  

CLOAUSSTP2  

UT  

2

1

TE  

REMO  

L/MUTE  

WIRING  

V10O  

V

CLASS 2  

INPUTS2  

1

Terminal Block  

Zip-Tie  

STANDBY  

LEVEL  

2

1

0

US  

2

0

C

1

z

L

A

APPARA  

U

IS  

D

TIEO  

D

/V1ITD7  

U

PROT  

ETSTOLIMIT  

EC  

ERT/  

,

50-60H  

100-240V  

1.3A  

SIGNAL  

LINE  

L

Hot  

Terminal (  

NEUTRAL  

N

Neutral  

Terminal (  

3

.

Remove the 2 screws holding the hot (line) and neutral  

wires from the terminal block on the PCB.  

Ground  

Wire Nut  

Blue Wire  

Brown Wire  

100-240V 1.3A  

Conduit Nut  

50-60Hz  

EMT Adapter Plate  

L

N

Remove nut  

1

1. Connect the ground wire, as shown above, to the  

grounding stud on the bottom of the enclosure using the  

nut that was removed in step 4.  

Remove screws  

both sides) to release  

IEC connector plate.  

(

1

2. Replace the cover of the XPA by attaching the 8 screws that  

were removed in step 2.  

4

5

.

Remove the ground wire nut from the grounding stud on  

the bottom of the enclosure, as shown above.  

.

Remove the 2 screws from the IEC plate, and remove the  

IEC connector plate and the attached wires through the  

rear panel of the XPA, as shown above.  

6

7

.

.

Thread the 18-gauge power wires through the length of the  

electrical conduit tube.  

Install the EMT adapter plate with conduit attached into  

the opening from which the IEC connector was removed.  

in step 5.  

8

9

.

Slide the conduit nut over the bundle of wires exiting the  

conduit and onto the conduit itself. Hand tighten the  

conduit nut to the conduit.  

.

Attach the EMT adapter plate assembly to the XPA using  

the 2 screws that were removed in step 5.  

2

-8  

XTRA Series • Installation  

XTRA Series • Installation  

2-9  

• ← Previous
• Next page →

In addition to the user manual Extron electronic XPA 1002, we also provide a support panel to help you solve your problems with Extron electronic XPA 1002. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Extron electronic XPA 1002. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Extron electronic XPA 1002 - you will surely help many users by doing so.