User manual Kenwood KRF-V7060D

If you found this page, you probably have a problem and you need a user manual for the device Kenwood KRF-V7060D. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Kenwood KRF-V7060D it belongs to the category Stereo Receiver. A user manualKenwood KRF-V7060D is taken from the manufacturer, a Kenwood company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Kenwood KRF-V7060D directly. You can view the user manualKenwood KRF-V7060D directly online or save and store it on your computer.

Setting up the system  
Make connections as shown in the following pages.  
When connecting the related system components, be sure  
to refer to the instruction manuals supplied with the compo-  
nents you are connecting.  
Do not connect the power cord to a wall outlet until all  
connections are completed.  
Input mode settings  
CD/DVD, VIDEO 2 and DVD/6CH inputs each include jacks for digital  
audio input and analog audio input.  
The initial factory settings for audio signal playback for CD/DVD,  
DVD/6CH and VIDEO 2 are full auto.  
To use the analog audio input for playback instead (if, for example, you  
have connected a VCR to the VIDEO2 input), you must set the input  
mode for the corresponding input to the analog mode.  
After completing connections and turning on the receiver, follow the  
steps below.  
Notes  
1
. Be sure to insert all connection cords securely. If their connections are  
imperfect, sound may not be produced or there will be noise inference.  
. Be sure to remove the power cord from the AC outlet before plugging  
or unplugging any connection cords. Plugging/unplugging connection  
cords without disconnecting the power cord can cause malfunctions  
and may damage the unit.  
2
INPUT MODE  
3
. Do not connect power cords from components whose power con-  
sumption is larger than what is indicated on the AC outlet at the rear  
of this unit.  
Analog connections  
Audio connections are made using RCA pin cords. These cables transfer  
stereo audio signal in an analogform. This means the audio signal  
corresponds to the actual audio of two channels. These cables usually  
have 2 plugs on each end, one red for the right channel and one white for  
the left channel. These cables are usually packed together with the  
source unit, or are available at your local electronics retailer.  
Input Selector  
1
2
Use the Input Selector keys to select CD/DVD, VIDEO 2 or  
DVD/6CH.  
Press the INPUT MODE key.  
Each press switches the setting as follows:  
In DTS play mode  
FULL AUTO (digital input, analog input)  
DIGITAL MANUAL (digital input)  
Microcomputer malfunction  
If operation is not possible or an erroneous display appears, even  
though all connections have been made properly, reset the micro-  
computer referring to In case of difficulty.  
1
2
CAUTION  
Be sure to adhere to the following, or proper ventilation will be  
blocked causing damage or fire hazard.  
In CD/DVD, VIDEO 2, DVD/6CH play mode  
1
2
3
4
FULL AUTO (digital input, analog input)  
DIGITAL MANUAL (digital input)  
6CH INPUT (DVD/6CH input)  
ANALOG (analog input)  
Do not place any objects impairing heat radiation onto the top of the  
unit.  
Leave some space around the unit (from the largest outside  
dimension including projection) equal to or greater than, shown  
below.  
Top panel : 50 cm  
Side panel : 10 cm Back panel : 10 cm  
Digital input:  
Select this setting to play digital signals from a DVD, CD, or LD  
player.  
Analog input:  
Select this setting to play analog signals from a cassette deck, VCR,  
or record player.  
Auto detect:  
In FULL AUTOmode (AUTO DETECT indicator light up), the  
receiver detects the digital or analog input signals automatically.  
Priority is given to digital signal during input mode selection. The  
receiver will select the input mode and listening mode automatically  
during playback to match the type of input signal (Dolby Digital,  
PCM, DTS) and the speaker setting. The OPTICAL and COAXIAL  
indicator on the display will light up when digital signal is detected.  
If the input signal is analog, the ANALOG indicator will light up.  
To keep the receiver set to the currently selected listening mode,  
use the INPUT MODE key to select DIGITAL MANUAL(manual  
sound). However, even when this setting is selected, there may be  
cases in which the listening mode is selected automatically to  
match a Dolby Digital source signal depending on the combination  
of listening mode and source signal.  
If the INPUT MODE key is pressed quickly, sound may not be  
produced. Press the INPUT MODE key again.  
EN  
9
VR6050/01-09/EN  
9
4/9/02, 4:52 PM  

In addition to the user manual Kenwood KRF-V7060D, we also provide a support panel to help you solve your problems with Kenwood KRF-V7060D. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Kenwood KRF-V7060D. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Kenwood KRF-V7060D - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.