Using the remote control
CR-314 Remote Control
Note that greyed-out buttons on the remote control are DVD-
speciﬁc and are not used with the CD player.
Ensure that CD mode is selected using the CD/ DVD
toggle button. The ‘CD’ LED above the CD/ DVD
button is lit brieﬂy when CD mode is selected.
This allows direct access to individual tracks on the disc. To
select a track, press the corresponding keypad button and then
press . For tracks greater than 9, enter the digits in sequence.
For example, to play track 15, press and hold 1 until the number
on the display moves to the left, then press 5.
Turns the display on or off. Turning the display off generally
produces a slight improvement in sound quality.
CD/ DVD REMOTE
If you make a mistake whilst programming you can delete
the last entered track by pressing CLEAR. To delete all
the programmed tracks, press CLEAR repeatedly until ‘0’ is
This button enables you to repeat any section of music within
a track. Whilst the disc is playing, press the A–B button at the
start of the section you wish to repeat. ‘REPEAT’ is shown on
the display and the letter ‘A–’ ﬂashes. Press the button a second
time when you reach the end of the section you wish to repeat.
The ‘A–B’letters stop ﬂashing and remain lit. This section will
To exit the program facility, press PROG.
You can program a selection of up to 24 tracks from a
disc to play in any order. Select a track by using the
repeat until you press or
or . The forward search button
) moves forward within the selected loop.
buttons, then press PROG to program the track into
memory (‘PROGRAM’appears on the display to indicate that you
have started programming a sequence). Repeat these steps to
program the remaining tracks in your selection. Alternatively,
press PROG once and enter your track selection using the 0–9
To repeat the entire CD or a pre-programmed selection of tracks
press RPT once: ‘REPEAT’lights on the display. To repeat a
particular track, select that track and then press RPT twice so
that ‘REPEAT 1’is shown on the display. If you now select a
different track, that track is repeated instead.
The display shows the track numbers programmed, the total
length of the programmed sequence and the number of tracks
programmed (shown by a number below the word ‘STEP’).
To cancel the repeat function press RPT a third time.
Each time you enter a track the number below ‘STEP’increments
by one and ﬂashes until you press PROG to conﬁrm. If you fail to
press PROG within about ﬁve seconds the display stops ﬂashing
and you will have to reselect the track.
Search and Skip Track
Search backwards and forwards;
Skip track backwards and forwards (see page 5)
Opens and closes the CD tray
Press to play the program. Press again to replay the entire
sequence from the start. Press and hold CLEAR to erase the
programmed sequence. Press PROG again to exit the program
facility: the display ﬂashes ‘CONTINUE’and shows ‘0’.
Pause, Play and Stop (see page 5)
Stops sound to the speaker outputs of certain Arcam ampliﬁers.
Press once to shufﬂe play CD tracks (i.e. play them in
a random order). Press again to cancel shufﬂe play.
Volume +/ –
Adjusts the volume on Arcam remote-controllable ampliﬁers.
Note that the volume (+/ –) controls and MUTE button have
Press TITLE once to display the remaining time of the currently
playing track. Press again to display the time remaining of
the disc. Press a third time to turn the text display on.
Press TITLE again and the display reverts to its original setting,
showing the time elapsed for the current track.
no effect on the audio output level of the CD players.
For CDs with text, pressing TITLE once while the disc
is loaded but not playing displays the artist’s name.
Pressing TITLE a second time displays the total number of
tracks and the total playing time.
NOTE: Remember to install the two AAAbatteries supplied
before trying to use your remote control.
Do not place anything in front of the display area on the
CD player (where the IR receiver is located), or the remote
control may not work.