User manual Behringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496

If you found this page, you probably have a problem and you need a user manual for the device Behringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Behringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496 it belongs to the category Stereo System. A user manualBehringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496 is taken from the manufacturer, a Behringer company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Behringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496 directly. You can view the user manualBehringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496 directly online or save and store it on your computer.

The PAGE key allows you to select the variousUpaLgeTs RACURVE PRO DEQ2496  
within one menu.  
The functions performed by the keys A and B depend on  
the selected menu and are indicated in the display.  
This is the LC display of your ULTRACURVE PRO.  
The DEQ2496 has three DATA WHEELS, which can be  
used to select and edit various parameters—again  
depending on the currently selected menu. Often, they  
Fig. 2.5: Digital interfaces and RTA microphone input  
perform a dual function, i.e. you can edit by turning and  
pressing a data wheel. Pressing the data wheels also  
changes the scaling of many parameters (step width) or  
confirms/resets previously made entries.  
Your DEQ2496 features a digital optical interface for the  
transmission/reception of data in both AES/EBU and  
S/PDIF formats.  
The digital AES/EBU interface (XLR connectors) also  
sends/receives AES/EBU or S/PDIF signals.  
The AUX OUT phone jack is an additional stereo output,  
which allows you to tap the audio signal present at the  
digital outputs in analog form.  
The RTA/MIC IN XLR connector can be used to connect  
a measurement microphone providing an input signal for  
the real-time analyzer or SPL meter. This connector has a  
switchable +15 V phantom power supply for condenser  
microphones and can be set to microphone or line  
sensitivity (see chapter 3.11).  
Fig. 2.3: The menu keys of the DEQ2496  
With the menu keys you can select the individual menus  
of the various modules. They can also be used to select  
specific pages from these menus (like PAGE key). Each  
of these keys has a built-in LED, which lights up when the  
corresponding module starts modifying the sound. When  
the DEQ2496 receives MIDI data, the LED of the UTILITY  
key lights up briefly. Keep this key pressed for about 1 s  
to bypass active modules or re-activate disabled ones.  
This function refers only to those modules which can be  
edited in the BYPASS menu (see chapter 3.7).  
The MAX switch raises the maximum level present at the  
MAIN inputs/outputs from +12 dBu to +22 dBu.  
Use the POWER switch to put the DEQ2496 into operation.  
This switch should be set to “Off” before you connect the  
unit to the mains.  
Fig. 2.6: Input and output connectors  
These balanced XLR connectors provide the analog output  
signal of the DEQ2496.  
2
.2 Rear panel  
These balanced XLR inputs are used to connect analog  
input signals.  
Fig. 2.4: Mains, MIDI and wordclock connectors  
The FUSE HOLDER holds the mains fuse of the DEQ2496.  
Blown fuses must be replaced by fuses of the same type  
and rating. Please see the “SPECIFICATIONS” for further  
details.  
The mains connection is made using the enclosed power  
cord and a standard IEC receptacle.  
The MIDI jacks enable the DEQ2496 to communicate with  
a computer or other MIDI equipment. Incoming MIDI data  
are received on the MIDI IN, outgoing MIDI data are sent  
via the MIDI OUT. Received MIDI data are also present at  
the MIDI THRU jack, so as to pass them on unmodified to  
other devices.  
Use the WORDCLOCK input to synchronize your  
DEQ2496 to external equipment via a wordclock signal.  
This connector is on a BNC coaxial jack.  
2. CONTROL ELEMENTS  
7

In addition to the user manual Behringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496, we also provide a support panel to help you solve your problems with Behringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Behringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Behringer high-precision digital 24-bit/96 kHz EQ/RTA mastering processor DEQ2496 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.