User manual Aube Technologies TI073

If you found this page, you probably have a problem and you need a user manual for the device Aube Technologies TI073. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Aube Technologies TI073 it belongs to the category Switch. A user manualAube Technologies TI073 is taken from the manufacturer, a Aube Technologies company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Aube Technologies TI073 directly. You can view the user manualAube Technologies TI073 directly online or save and store it on your computer.

4
00-073-000-A ENG.fm Page 1 Wednesday, January 28, 2009 9:41 AM  
TI073  
User guide  
7-day Solar Programmable Wall Switch  
1
.
3.  
Applications  
The TI073 programmable wall switch can be used in a single-switch or 3-way installation with the following  
types of lighting:  
Quick Start-up  
n
p
Set the time and date before using the switch for the first time.  
Incandescent  
• Halogen  
• Low-voltage halogen with transformer  
• Fluorescent  
The TI073 will turn the lights on at sunset and turn them off at 11:00 pm by default. If these settings are  
appropriate for you, you only need to set the time and date (see shaded zone in the menu flowchart sheet).  
If the switch’s sunset time does not correspond to the actual sunset time, see sections 5.3.3 and 5.3.4.  
4.  
The TI073 switch cannot be used with a load of less than 40 W or more than 500 W.  
2
.
Installation  
Operation  
o
q
n
o
Cut power at the circuit breaker to avoid electric shock.  
Indicates the mode of  
operation (see Section 5.1)  
The icon indicates the current program  
has been activated at sunset.  
Remove the existing switch. (For a 3-way installation, identify and label the wire connected to the  
common” screw.)  
The  
icon indicates the current program  
Indicates the time and day  
Indicates the current program  
Indicates the load on/off state  
p
q
Install the new switch (see the appropriate section below).  
Apply power at the circuit breaker.  
has been activated at sunrise.  
Press this button to display today’s sunrise time.  
Press this button to display today’s sunset time.  
WARNING: Disconnect power to the switch when replacing a light bulb (see section 4).  
Briefly press this button to turn the  
lights on or off. See “Temporary  
Override” in Section 5.1.4.  
Press for 3 seconds to enter the  
setup menus.  
SINGLE-SWITCH INSTALLATION  
black  
white  
black  
white  
The LED illuminates when the load state is on.  
1
VAC  
20  
yellow (3-WAY)  
black (LINE)  
Safety switch  
Before replacing a light bulb, pull out to disconnect power to the switch.  
This prevents, while the bulb is out, any possible short circuit which will  
damage the switch. Push back in after the light bulb is replaced.  
green (GND)  
black (LOAD)  
5
.
Setup Menus  
r
1
VAC  
20  
black  
white  
yellow (3-WAY)  
black (LINE)  
Press the main button for 3 seconds to enter the setup menus. Refer to  
the menu flowchart sheet on how to navigate the menus.  
white  
black  
(3 sec.)  
green (GND)  
black (LOAD)  
5.1  
Mode Menu  
Use the Mode menu to select one of the three modes of operation (see sections 5.1.1 to 5.1.3).  
Connect the LINE and 3-WAY wires to the line (120 V) wire and LOAD wire to the load. Connect the GND  
wire to a ground screw inside the electrical box.  
5
.1.1 Manual Mode  
In Manual mode, the TI073 operates like a regular switch. To turn the lights on or off, briefly  
press the main button. The icon appears when the switch is in Manual mode.  
EXISTING 3-WAY INSTALLATION  
1
VAC  
20  
black  
white  
black  
white  
black (LINE)  
green (GND)  
black (LOAD)  
jumper  
5
In Automatic mode, the TI073 turns the lights on or off according to the set programs (see  
.1.2 Automatic Mode  
Section 5.4). The icon as well as the current program number are displayed.  
black  
red  
yellow (3-WAY)  
three-way  
switch  
white  
5
In Random mode, the TI073 has no specific times to turn the lights on or off. This mode is  
designed to give the impression the house is occupied during your absence. It is similar to  
the Automatic mode except there is no fixed program. The programs are automatically set  
to different times by the TI073 every day. The  
Random mode.  
.1.3 Random Mode  
Connect the LOAD wire on the TI073 to the “common” wire, which you identified when removing the old  
switch. Connect the GND wire to a ground screw inside the electrical box. Connect the LINE and 3-WAY  
wires to the two remaining wires. At the other 3-way switch, connect the jumper wire between the “common”  
screw and the screw where the LINE wire of the TI073 is connected.  
icon appears when the switch is in  
NEW 3-WAY INSTALLATION  
The first “On” program occurs at sunset. Each “On” program lasts between 1 hour and 1  
hour and 30 minutes; each “Off” program lasts between 15 and 30 minutes. The last “Off”  
program occurs between 10:30 pm and midnight.  
black  
white  
black  
white  
1
VAC  
20  
black  
black (LINE)  
5
.1.4 Temporary Override  
green (GND)  
black (LOAD)  
When the TI073 is in Automatic or Random mode, you can press the main button at any time to override the  
default state for the current program. The lights will turn off if they are on and vice versa. The new state icon  
(On or Off) flashes to indicate that the state is temporary. The new state is maintained until you press the  
main button again or till the next “On” or “Off” program.  
single-pole  
switch  
yellow (3 WAY)  
white  
TI073  
400-073-000-A  
2009-01-28  
1/2  

In addition to the user manual Aube Technologies TI073, we also provide a support panel to help you solve your problems with Aube Technologies TI073. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Aube Technologies TI073. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Aube Technologies TI073 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.