User manual D-Link DGS-1016D

If you found this page, you probably have a problem and you need a user manual for the device D-Link DGS-1016D. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database D-Link DGS-1016D it belongs to the category Switch. A user manualD-Link DGS-1016D is taken from the manufacturer, a D-Link company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device D-Link DGS-1016D directly. You can view the user manualD-Link DGS-1016D directly online or save and store it on your computer.

D-Link DGS-1016D/DGS-1024D Unmanaged Gigabit Ethernet Switch  
Safety Instructions (continued)  
To help avoid damaging your system, be sure the voltage selection Switch (if provided)  
on the power supply is set to match the power available at your location:  
115 volts (V)/60 hertz (Hz) in most of North and South America and some Far  
Eastern countries such as South Korea and Taiwan  
100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan.  
230 V/50 Hz in most of Europe, the Middle East, and the Far East.  
Also be sure that attached devices are electrically rated to operate with the power  
available in your location.  
Use only approved power cable(s). If you have not been provided with a power cable  
for your system or for any AC-powered option intended for your system, purchase a  
power cable that is approved for use in your country. The power cable must be rated for  
the product and for the voltage and current marked on the product's electrical ratings  
label. The voltage and current rating of the cable should be greater than the ratings  
marked on the product.  
To help prevent an electric shock, plug the system and peripheral power cables into  
properly grounded electrical outlets. These cables are equipped with three-prong plugs  
to help ensure proper grounding. Do not use adapter plugs or remove the grounding  
prong from a cable. If you must use an extension cable, use a 3-wire cable with properly  
grounded plugs.  
Observe extension cable and power strip ratings. Make sure that the total ampere rating  
of all products plugged into the extension cable or power strip does not exceed 80  
percent of the ampere ratings limit for the extension cable or power strip.  
To help protect your system from sudden, transient increases and decreases in electrical  
power, use a surge suppressor, line conditioner, or uninterruptible power supply (UPS).  
Position system cables and power cables carefully; route cables so that they cannot be  
stepped on or tripped over. Be sure that nothing rests on any cables.  
Do not modify power cables or plugs. Consult a licensed electrician or your power  
company for site modifications. Always follow your local/national wiring rules.  
When connecting or disconnecting power to hot-pluggable power supplies, if offered  
with your system, observe the following guidelines:  
Install the power supply before connecting the power cable to the power supply.  
Unplug the power cable before removing the power supply.  
If the system has multiple sources of power, disconnect power from the system  
by unplugging all power cables from the power supplies.  
Move products with care; ensure that all casters and/or stabilizers are firmly connected  
to the system. Avoid sudden stops and uneven surfaces.  
vi  

In addition to the user manual D-Link DGS-1016D, we also provide a support panel to help you solve your problems with D-Link DGS-1016D. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with D-Link DGS-1016D. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with D-Link DGS-1016D - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.