User manual Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC

If you found this page, you probably have a problem and you need a user manual for the device Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC it belongs to the category Vacuum Cleaner. A user manualOreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC is taken from the manufacturer, a Oreck company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC directly. You can view the user manualOreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC directly online or save and store it on your computer.

E
N
G
L
I
S
H
Replacing Disposable Odor Fighting Dust Bag  
WARNING: Unplug cord from electrical outlet before servicing.  
BAG REMOVAL:  
Maintenance.  
6
7
8
Unzip outer bag completely.  
Pull bag cardboard collar to release bag dock door from connector. Bag dock door will hinge downward.  
®
Gently pull bag cardboard collar upward out of the bag dock. Saniseal dust seal will close automatically.  
BAG INSTALLATION:  
9
Slide the cardboard collar completely onto bag dock door.  
1
0 Firmly push bag dock door with both thumbs on indication point until it snaps.  
ENFONCEZ JUSQU’À  
ENTENDRE UN BRUIT  
PRESIONE HASTA  
ESCUCHAR UN  
CHASQUIDO DE SUJECIÓN  
6
7
8
8
10  
Replacing Worn Belt  
WARNING: Unplug cord from electrical outlet before servicing.  
11 Remove the replacement belt from the storage channel.  
1
1
1
1
1
2 Remove the door by removing the hold down screw located on side of power head.  
3 Fold door away from the power head and lift it away.  
4 Remove the belt from the motor drive shaft and brush roll pulley.  
5 Loop the new belt over the brush roll pulley. Place the opposite end of the belt on the motor drive shaft.  
3 Replace the door by placing the bottom tab on door into slots located inside power head and pressing the  
door closed.  
1
2 Replace the hold down screw and tighten.  
11  
12  
13  
14  
15  
Adjusting or Replacing Brushroll  
WARNING: Unplug cord from electrical outlet before servicing.  
To determine if the brushroll is worn, place a firm straight edge across the nozzle opening. If brushroll bristles do  
not extend beyond baseplate, brushroll should be adjusted.  
1
1
1
1
6 Remove the baseplate by removing 5 screws. Then, remove the belt and brushroll from the housing.  
7 Rotate both bearing assemblies at ends or brushroll to show “OLD” and replace in the holding channels in the housing.  
8 Note: The bearing assembly setting market “OLD” has no ribs on the top of the assembly.  
9 The one marked “NEW” has several ribs. When rotating bearings, make sure both bearing assembly settings are  
the same and face up when replacing the brushroll.  
1
1
5 Reassemble the belt.  
6 Reassemble the baseplate.  
6

In addition to the user manual Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC, we also provide a support panel to help you solve your problems with Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.