User manual Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC

If you found this page, you probably have a problem and you need a user manual for the device Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC it belongs to the category Vacuum Cleaner. A user manualOreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC is taken from the manufacturer, a Oreck company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC directly. You can view the user manualOreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC directly online or save and store it on your computer.

E
N
G
L
I
S
H
Stuffing or Blockage  
Maintenance.  
IMPORTANT: On plush and new carpets, stuffing may occur inside the the intake tube and the lower tube  
assembly. This is due to excessive fuzz and loose cuttings in the carpet. Stuffing could occur for the first few  
cleanings until all the loose material is removed. Due to the high efficiency of the cleaner, many older carpets  
will cause stuffing when the cleaner is first used on them. If your vacuum cleaner does not pick up properly, or  
makes unusual noise and the outer bag does not fluff up or balloon open, follow these steps:  
WARNING: Unplug cord from electrical outlet before servicing.  
2
4 Check for blockage at the mouth of the intake opening. If there is blockage, remove it with long-nose pliers,  
a screwdriver or coat hanger. If you can not reach the blockage, remove baseplate. Remove the baseplate by  
removing 5 screws (see “Adjusting or Replacing Brushroll”).  
2
2
2
2
2
5 If the blockage is not at the base, remove lower tube. Unhook bag spring, releasing bottom of bag.  
6 Twist lower collar counterclockwise to slide up. Pull tube out of base.  
7 Check for blockage. If blockage is in the tube, remove with a coat hanger.  
8 If tube is not blocked, look into fan housing. Remove debris with long-nose pliers, a screwdriver or coat hanger.  
6 To reassemble, check O-ring on tube, and replace if damaged. Replace tube by first lining up slot at base of  
tube with tab inside fan housing. Insert tube and push down until the tube is seated. Make sure O-ring is in  
place against fan housing opening. Replace and tighten collar until collar locking tabs are locked in place.  
Reattach bag spring.  
2
9 Many times blockage occurs due to a full dust bag causing dirt to back down the air flow system. When that  
happens, the blockage will be at the top of the system, starting in the area where the dust bag connects to the  
connector assembly.  
Note: If the above actions do not correct the problem, contact an Oreck authorized service center or call the  
customer service center. US: 1-800-989-3535 Canada: 1-888-676-7325  
2
4
25  
26  
27  
28  
29  
Problem  
Cleaner will not run.  
Check  
•Not plugged in properly.  
What to do  
•Be sure cleaner is firmly plugged into wall outlet.  
Trouble-  
shooting.  
No electricity in wall outlet. •Check electrical source – fuse or circuit breaker.  
Cleaner does not pick up. •Filter Bag is full.  
•Replace filter bag. See “Replacing Disposable  
Odor Fighting Dust Bag”.  
Service problems that  
appear to be major can  
often be solved easily.  
You can be your own  
troubleshooter by  
Nozzle or intake pivot  
clogged.  
•Clear obstruction.  
Belt is broken or stretched. •Replace belt.  
Brush is worn.  
•See “Adjusting or Replacing Brush roll”.  
Bag tube clogged.  
•Clear obstruction.  
•Change bag.  
reviewing this guide.  
Bag pores are clogged  
with fine dust.  
All other servicing  
should be done by an  
Oreck authorized  
service center.  
•Impeller fan is broken.  
•Return to Service Center for repair.  
•Revolving brush is not  
even at both ends.  
•Check bearing seal. Make sure words “OLD”  
or “NEW” at each end.  
Unit still does not  
operate properly.  
•Check all the  
above points.  
•Contact Oreck for service.  
8

In addition to the user manual Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC, we also provide a support panel to help you solve your problems with Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.