Manual de instrucciones Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC

Si has encontrado esta página, seguramente tienes un problema y necesitas el manual de instrucciones para el dispositivo Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. Recuerda comprobar si es el manual exacto para el dispositivo que buscas. En nuestra base Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC pertenece a la categoría Aspiradoras. El manual Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC es del fabricante, la empresa Oreck - es un documento oficial y si tienes alguna duda acerca de su contenido, contacta directamente con el fabricante del dispositivo Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. El manual Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC se puede ver directamente online o guardar y almacenar en tu ordenador.

E
N
G
L
I
S
H
Replacing Disposable Odor Fighting Dust Bag  
WARNING: Unplug cord from electrical outlet before servicing.  
BAG REMOVAL:  
Maintenance.  
6
7
8
Unzip outer bag completely.  
Pull bag cardboard collar to release bag dock door from connector. Bag dock door will hinge downward.  
®
Gently pull bag cardboard collar upward out of the bag dock. Saniseal dust seal will close automatically.  
BAG INSTALLATION:  
9
Slide the cardboard collar completely onto bag dock door.  
1
0 Firmly push bag dock door with both thumbs on indication point until it snaps.  
ENFONCEZ JUSQU’À  
ENTENDRE UN BRUIT  
PRESIONE HASTA  
ESCUCHAR UN  
CHASQUIDO DE SUJECIÓN  
6
7
8
8
10  
Replacing Worn Belt  
WARNING: Unplug cord from electrical outlet before servicing.  
11 Remove the replacement belt from the storage channel.  
1
1
1
1
1
2 Remove the door by removing the hold down screw located on side of power head.  
3 Fold door away from the power head and lift it away.  
4 Remove the belt from the motor drive shaft and brush roll pulley.  
5 Loop the new belt over the brush roll pulley. Place the opposite end of the belt on the motor drive shaft.  
3 Replace the door by placing the bottom tab on door into slots located inside power head and pressing the  
door closed.  
1
2 Replace the hold down screw and tighten.  
11  
12  
13  
14  
15  
Adjusting or Replacing Brushroll  
WARNING: Unplug cord from electrical outlet before servicing.  
To determine if the brushroll is worn, place a firm straight edge across the nozzle opening. If brushroll bristles do  
not extend beyond baseplate, brushroll should be adjusted.  
1
1
1
1
6 Remove the baseplate by removing 5 screws. Then, remove the belt and brushroll from the housing.  
7 Rotate both bearing assemblies at ends or brushroll to show “OLD” and replace in the holding channels in the housing.  
8 Note: The bearing assembly setting market “OLD” has no ribs on the top of the assembly.  
9 The one marked “NEW” has several ribs. When rotating bearings, make sure both bearing assembly settings are  
the same and face up when replacing the brushroll.  
1
1
5 Reassemble the belt.  
6 Reassemble the baseplate.  
6

Además del manual Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC facilitamos un panel de soporte que te ayudará a solucionar tus problemas con Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. Si tienes alguna pregunta, puedes escribirla en el formulario más abajo. Otros usuarios que entran aquí tendrán la oportunidad de ayudarte en la solución de tu problema con Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC. Recuerda que también puedes compartir tu solución. Si has logrado solucionar el problema, por favor escribe aquí la descripción y la solución del problema con Oreck Powerful,Lightweight Upright Vacuum XL Silver Series 76011-01REVC - seguro que ayudarás a muchos usuarios.

¿Tienes problemas con un dispositivo? Haz una pregunta - nuestros usuarios pueden ayudarte

Nadie ha añadido un comentario para este dispositivo/manual todavía