このページへお越しの方は、おそらくデバイスWhirlpool GXW6530DXSに関する問題を抱えており、その説明書を必要としていることでしょう。お探しの説明書がお持ちのデバイスのそれであることを必ずご確認ください、お探しのWhirlpool GXW6530DXSは、このデータベースではカテゴリー範囲に属します。 説明書Whirlpool GXW6530DXSはメーカーWhirlpoolの発行するものです　－　これは公式文書であるため、その内容に疑問がある場合はデバイスWhirlpool GXW6530DXSの製造元に直接お問い合わせください。説明書Whirlpool GXW6530DXSはオンラインで直接見たりコンピュータにダウンロードし保存したりすることができます。

INSTALLATION INSTRUCTIONS  

PrepareLocation  

8. Mark centers of the fastener locations through the template  

to the wall.  

■

■

■

It is recommended that the vent system be installed before  

hood is installed.  

IMPORTANT: All screws must be installed into wood. If there  

is no wood to screw into, additional wall framing supports  

may be required.  

Before making cutouts, make sure there is proper clearance  

within the ceiling or wall for exhaust vent.  

Check your ceiling height and the hood height maximum  

before you select your hood.  

Remove the template.  

9

.

Drill ³⁄₁₆" (4.8 mm) pilot holes at all locations where screws are  

being installed into wood.  

1

.

Disconnect power.  

2.  

Determine which venting method to use: roof, wall, or non-  

vented.  

1

0. Install the 2 - 5 x 45 mm mounting screws. Leave a  

⁄₄" (6.4 mm) gap between the wall and the back of the  

screw head to slide range hood into place.  

¹

3.  

Select a flat surface for assembling the range hood. Place  

covering over that surface.  

¹

⁄₄"  

(6.4 mm)  

WARNING  

Excessive Weight Hazard  

Use two or more people to move and install  

range hood.  

Vent Cover Bracket Installation  

Failure to do so can result in back or other injury.  

1

1. Attach vent cover bracket to wall flush to the ceiling using  

2

- 5 x 45 mm screws.  

4.  

Using 2 or more people, lift range hood onto covered surface.  

Range Hood Mounting Screws Installation  

5

.

.

Determine and mark the centerline on the wall where the  

canopy hood will be installed.  

A

6

Select a mounting height between a minimum of  

24" (61.0 cm) for an electric cooking surface, a minimum  

B

of 27" (68.6 cm) for a gas cooking surface, and a suggested  

maximum of 36" (91.4 cm) above the range to the bottom  

of the hood. Mark a reference line on the wall.  

7.  

Tape template in place, aligning the template centerline and  

bottom of template with hood bottom line and with the  

centerline marked on the wall.  

C

A

A. Ceiling  

B. Wall  

DRILL2(TWO)3/16"PILOTHOLESTHROUGHSTUDSORREARWALLSUPPORT  

C. Centerline  

REARWALL  

MOUNTINGTEMPLATE  

Complete Preparation  

CL  

ALIGNBOTTOM EDGE  

WITHPENCILLINE  

INDICATINGBOTTOM  

OFTHEHOOD  

1. Determine and make all necessary cuts in the wall for the vent  

system. Install the vent system before installing the hood. See  

InstallationHeight  

HorizontalLine  

“Venting Requirements” section.  

2.  

Determine the required height for the home power supply  

cable and drill a 1¼" (3.2 cm) hole at this location.  

B

C

A. Centerline  

B. Fastener locations  

C. Mounting height reference  

hood bottom line)  

3. Run the home power supply cable according to the National  

Electrical Code or CSA Standards and local codes and  

ordinances. There must be enough ½" conduit and wires from  

the fused disconnect (or circuit breaker) box to make the  

connection in the hood’s electrical terminal box.  

(

NOTE: Do not reconnect power until installation is complete.  

4. Use caulk to seal all openings.  

7

• ← Previous
• Next page →

Whirlpool GXW6530DXSの説明書の他にも、あなたがWhirlpool GXW6530DXSとその問題を解決するのに役立つヘルプパネルを提供しています。何か質問がある場合は、以下のフォームから送信することができます。他のユーザーがここを訪問し、あなたのWhirlpool GXW6530DXSに関する問題解決を支援してくれるかもしれません。また、あなたがたどり着いた解決方法についてもご共有することをお忘れなく。うまく解決できた場合はWhirlpool GXW6530DXSに関する問題とその解決法についてこちらにご記入ください　－　きっと数多くのユーザーに役立つことでしょう。