このページへお越しの方は、おそらくデバイスWilton PF3-EZに関する問題を抱えており、その説明書を必要としていることでしょう。お探しの説明書がお持ちのデバイスのそれであることを必ずご確認ください、お探しのWilton PF3-EZは、このデータベースではカテゴリーノコギリに属します。 説明書Wilton PF3-EZはメーカーWiltonの発行するものです　－　これは公式文書であるため、その内容に疑問がある場合はデバイスWilton PF3-EZの製造元に直接お問い合わせください。説明書Wilton PF3-EZはオンラインで直接見たりコンピュータにダウンロードし保存したりすることができます。

6

.

.

Tighten the screws firmly with a 19mm  

wrench.  

7

Insert the pin assembly into the hole (Figure  

2

). You may need to rotate it until it seats  

properly in the hole.  

8

.

.

Install a flat washer and cast iron handle  

(

Figure 2) to the threads of the top screw as  

shown, by screwing the handle down  

clockwise onto the screw threads.  

9

In the area above the pin, remove the hex  

nut from the screw with a 19mm wrench, but  

leave the flat washer in place. In place of  

the hex nut, install the cam handle (Figure  

Figure 2  

Figure 3  

Figure 4  

2

). Screw the cam handle clockwise onto  

the threads (the cam handle will contact the  

pin on each rotation and push the pin  

downward.) Tighten the cam handle.  

1

0. Loosen the hex nut (A, Figure 3) with a  

2mm wrench, and back off the set screw  

1

(

B, Figure 3) with a 4mm hex wrench, until  

the shaft of the handwheel can be inserted  

freely into the hole in the bracket (Figure 3).  

The handwheel should be positioned so that  

the pinion on its shaft is approximately  

centered with the keyway of the bracket.  

1

1. Turn the set screw (B, Figure 3) clockwise  

into the shaft just enough to prevent the  

handwheel from slipping out. Do not  

overtighten the set screw. Tighten the hex  

nut (A, Figure 3).  

12. Loosen the handle above the bracket  

(

Figure 4).  

1

3. The end of the horizontal arm that has the  

rack extending to the end will be inserted  

into the bracket. Insert the horizontal arm,  

with the rack pointed downward, into the  

bracket. The rack will fit through the keyway  

in the bracket. See Figure 4. Continue to  

push the horizontal arm into the bracket  

while slightly rotating the handwheel  

counterclockwise, until the rack and pinion  

mesh. The horizontal arm can now be  

moved into the bracket by rotating the  

handwheel.  

1

4. Install the elevating column onto the  

horizontal arm (Figure 5). Make sure the  

horizontal arm slides all the way into the  

sleeve of the elevating column (The end of  

the rack on the horizontal arm will almost  

touch the sleeve). Check that the elevating  

column assembly is in the vertical position.  

Tighten the two screws on the sleeve  

(

Figure 5) with a 19mm wrench.  

15. Install a flat washer and handle on the  

screw of the elevating column (Figure 5).  

Figure 5  

10  

• ← Previous
• Next page →

Wilton PF3-EZの説明書の他にも、あなたがWilton PF3-EZとその問題を解決するのに役立つヘルプパネルを提供しています。何か質問がある場合は、以下のフォームから送信することができます。他のユーザーがここを訪問し、あなたのWilton PF3-EZに関する問題解決を支援してくれるかもしれません。また、あなたがたどり着いた解決方法についてもご共有することをお忘れなく。うまく解決できた場合はWilton PF3-EZに関する問題とその解決法についてこちらにご記入ください　－　きっと数多くのユーザーに役立つことでしょう。