取扱説明書Wilton PF3-EZ

このページへお越しの方は、おそらくデバイスWilton PF3-EZに関する問題を抱えており、その説明書を必要としていることでしょう。お探しの説明書がお持ちのデバイスのそれであることを必ずご確認ください、お探しのWilton PF3-EZは、このデータベースではカテゴリーノコギリに属します。 説明書Wilton PF3-EZはメーカーWiltonの発行するものです - これは公式文書であるため、その内容に疑問がある場合はデバイスWilton PF3-EZの製造元に直接お問い合わせください。説明書Wilton PF3-EZはオンラインで直接見たりコンピュータにダウンロードし保存したりすることができます。

NOTE: The handle can be pivoted out of the  
way if necessary. Lift up on the handle,  
rotate the handle on its pin, then release the  
handle, making sure it fully seats itself on  
the pin.  
1
6. Mount the stock feeder to the elevating  
column by sliding the stud of the stock  
feeder into the hole of the pivot joint (Figure  
6
). Install the remaining flat washer and  
handle onto the stud, and tighten the  
handle.  
Grounding Instructions  
Electrical connections must  
be made by  
a
qualified electrician in  
compliance with all relevant codes. This  
machine must be properly grounded to help  
prevent electrical shock and possible fatal  
injury.  
As received from the factory, the PF3-EZ Stock  
Feeder will run on either 230 volt or 460 volt,  
depending upon your particular model. Make  
sure the voltage of your power supply matches  
the specifications on the motor plate of the  
Stock Feeder.  
Figure 6  
You may either connect an appropriate UL/CSA  
listed plug or “hard-wire” the machine directly to  
a control panel. If hard-wired to a panel, make  
sure a disconnect is available for the operator.  
The Stock Feeder must comply with all local and  
national codes after being wired. If it is to be  
hard-wired, make sure the fuses have been  
removed or the breakers have been tripped in  
the circuit to which the Stock Feeder will be  
connected. Place a warning placard on the fuse  
holder or circuit breaker to prevent it being  
turned on while the machine is being wired.  
Refer to “Electrical Connections” on page 25 for  
connecting the motor leads.  
This machine must be grounded. In the event of  
a malfunction or breakdown, grounding provides  
a path of least resistance for electric current, to  
reduce the risk of electric shock to the operator.  
Improper connection of the equipment-  
grounding conductor can result in a risk of  
electric shock. The conductor, with insulation  
having an outer surface that is green with or  
without yellow stripes, is the equipment-  
grounding conductor. If repair or replacement of  
the electric cord or plug is necessary, do not  
connect the equipment-grounding conductor to a  
live terminal.  
Repair or replace a damaged or worn cord  
immediately.  
11  

Wilton PF3-EZの説明書の他にも、あなたがWilton PF3-EZとその問題を解決するのに役立つヘルプパネルを提供しています。何か質問がある場合は、以下のフォームから送信することができます。他のユーザーがここを訪問し、あなたのWilton PF3-EZに関する問題解決を支援してくれるかもしれません。また、あなたがたどり着いた解決方法についてもご共有することをお忘れなく。うまく解決できた場合はWilton PF3-EZに関する問題とその解決法についてこちらにご記入ください - きっと数多くのユーザーに役立つことでしょう。

デバイスの問題をお抱えですか?質問しましょう - 他のユーザーが助けてくれることでしょう

このデバイス/説明書のためのコメントはまだ投稿されていません。