このページへお越しの方は、おそらくデバイスWilton PF3-EZに関する問題を抱えており、その説明書を必要としていることでしょう。お探しの説明書がお持ちのデバイスのそれであることを必ずご確認ください、お探しのWilton PF3-EZは、このデータベースではカテゴリーノコギリに属します。 説明書Wilton PF3-EZはメーカーWiltonの発行するものです　－　これは公式文書であるため、その内容に疑問がある場合はデバイスWilton PF3-EZの製造元に直接お問い合わせください。説明書Wilton PF3-EZはオンラインで直接見たりコンピュータにダウンロードし保存したりすることができます。

General Operating Instructions  

1.  

2.  

3.  

4.  

Make sure all locking handles are tight  

before operating the Stock Feeder.  

The Stock Feeder should be used in  

conjunction with a fence on the table saw.  

The rollers must grip the offcut as well as  

the part of the workpiece being fed.  

Position the Stock Feeder so that the axis of  

the saw blade lines up between the infeed  

roller and center roller. See Figure 13. This  

will allow the Stock Feeder to grip the near  

part of the workpiece as it enters the blade,  

as well as the offcut of the workpiece as it  

leaves the blade.  

Figure 13  

5.  

Rotate the Stock Feeder so that the  

direction of feed is angled slightly toward the  

fence by approximately 3/16” (5mm); that is,  

the outfeed roller should be slightly closer to  

the fence than the infeed roller. See Figure  

(

guard removed for clarity)  

13.  

IMPORTANT: Do not position the stock  

feeder in such a way that the rollers will  

interfere with, or be damaged by, the blade.  

6

.

.

The Stock Feeder should be adjusted for  

height so that the distance between the  

table and the feed rollers is approximately  

1

/8” (3mm) less than the thickness of the  

workpiece. See Figure 14.  

7

The feed rollers have a spring suspension,  

which will exert the necessary pressure  

against the workpiece. This pressure  

feed  

resistance, so that a workpiece of varying  

thickness can be fed through the Stock  

Feeder without adjustments.  

increases  

automatically  

with  

8

.

.

If a workpiece becomes jammed during  

cutting operation, shut off the table saw and  

the Stock Feeder. Then raise the Stock  

Feeder, remove workpiece, re-position the  

Stock Feeder and begin the cutting  

operation again.  

Figure 14  

9

Using hardwood with the Stock Feeder may  

increase the friction between workpiece and  

saw table. Keep the saw table rust-free and  

smooth by using paste wax or other  

necessary means.  

Spacers  

Three spacers are included with the Stock  

Feeder. These are used to increase the kerf  

spacing between inner and outer rollers. See  

Figure 15.  

Figure 15  

14  

• ← Previous
• Next page →

Wilton PF3-EZの説明書の他にも、あなたがWilton PF3-EZとその問題を解決するのに役立つヘルプパネルを提供しています。何か質問がある場合は、以下のフォームから送信することができます。他のユーザーがここを訪問し、あなたのWilton PF3-EZに関する問題解決を支援してくれるかもしれません。また、あなたがたどり着いた解決方法についてもご共有することをお忘れなく。うまく解決できた場合はWilton PF3-EZに関する問題とその解決法についてこちらにご記入ください　－　きっと数多くのユーザーに役立つことでしょう。