このページへお越しの方は、おそらくデバイスDialogic SS7G22に関する問題を抱えており、その説明書を必要としていることでしょう。お探しの説明書がお持ちのデバイスのそれであることを必ずご確認ください、お探しのDialogic SS7G22は、このデータベースではカテゴリーサーバーに属します。 説明書Dialogic SS7G22はメーカーDialogicの発行するものです　－　これは公式文書であるため、その内容に疑問がある場合はデバイスDialogic SS7G22の製造元に直接お問い合わせください。説明書Dialogic SS7G22はオンラインで直接見たりコンピュータにダウンロードし保存したりすることができます。

Chapter 1 Warnings and Cautions  

WARNING  

IF AC POWER SUPPLIES ARE INSTALLED:  

MAINS AC POWER DISCONNECT:  

The AC power cord(s) is considered the mains disconnect for the product and must be  

readily accessible when installed. If the individual product power cord(s) will not be  

readily accessible for disconnection then you are responsible for installing an AC power  

disconnect for the entire rack unit. This main disconnect must be readily accessible,  

and it must be labelled as controlling power to the entire rack unit, not just to this  

product. To remove all power, two AC cords must be removed.  

GROUNDING THE RACK INSTALLATION:  

To avoid the potential for an electrical shock hazard, you must include a third wire  

safety ground conductor with the rack installation. If the product power cord is  

plugged into an AC outlet that is part of the rack, then you must provide proper  

grounding for the rack itself. If the product power cord is plugged into a wall AC outlet,  

the safety ground conductor in the power cord provides proper grounding only for this  

product. You must provide additional, proper grounding for the rack and other devices  

installed in it.  

OVERCURRENT PROTECTION:  

The product is designed for an AC line voltage source with up to 20 Amps of  

overcurrent protection per cord feed. If the power system for the equipment rack is  

installed on a branch circuit with more than 20 Amps of protection, you must provide  

supplemental protection for the product. The overall current rating of the product  

configured with two power supplies is less than 2.5 Amps.  

WARNING  

AC POWER CORD:  

Do not attempt to modify or use an AC power cord that is not the exact type required.  

You must use a power cord that meets the following criteria:  

1

. Rating: For U.S./Canada cords must be UL Listed/CSA Certified type SJT, 18-3  

AWG. For outside U.S./Canada cords must be flexible harmonized (<HAR>) or VDE  

certified cord with 3 x 0.75mm conductors rated 250 VAC.  

2

. Connector, wall outlet end: Cords must be terminated in grounding-type male plug  

designed for use in your region. The connector must have certification marks  

showing certification by an agency acceptable in your region and for U.S. must be  

rated 125% of overall current rating of the product.  

3. Connector, product end: The connectors that plug into the AC receptacle on this  

product must be an IEC 320, sheet C19, type female connector.  

4

. Cord length: Cords must be less than 4.5 meters (14.76 feet) long.  

8

• ← Previous
• Next page →

Dialogic SS7G22の説明書の他にも、あなたがDialogic SS7G22とその問題を解決するのに役立つヘルプパネルを提供しています。何か質問がある場合は、以下のフォームから送信することができます。他のユーザーがここを訪問し、あなたのDialogic SS7G22に関する問題解決を支援してくれるかもしれません。また、あなたがたどり着いた解決方法についてもご共有することをお忘れなく。うまく解決できた場合はDialogic SS7G22に関する問題とその解決法についてこちらにご記入ください　－　きっと数多くのユーザーに役立つことでしょう。