取扱説明書SpeakerCraft NOT FOUND AIM LCR3

このページへお越しの方は、おそらくデバイスSpeakerCraft NOT FOUND AIM LCR3に関する問題を抱えており、その説明書を必要としていることでしょう。お探しの説明書がお持ちのデバイスのそれであることを必ずご確認ください、お探しのSpeakerCraft NOT FOUND AIM LCR3は、このデータベースではカテゴリースピーカーに属します。 説明書SpeakerCraft NOT FOUND AIM LCR3はメーカーSpeakerCraftの発行するものです - これは公式文書であるため、その内容に疑問がある場合はデバイスSpeakerCraft NOT FOUND AIM LCR3の製造元に直接お問い合わせください。説明書SpeakerCraft NOT FOUND AIM LCR3はオンラインで直接見たりコンピュータにダウンロードし保存したりすることができます。

PRINTING INSTRUCTIONS: AIM LCR3 MANUAL - INK: BLACK - MATERIAL: 80lb Gloss - SIZE: 8.500” x 11.000”  
determined there aren’t any obstructions in your desired mounting location, start cutting the finished  
hole at a 90º angle to the wall surface.  
FIGURE 5  
5
. Add insulation. If the area in the wall is not already insulated, add an adequate amount of insulation  
material to fill the wall cavity. If the insulation material used is faced with foil or paper, position the foil  
or paper away from the speaker.  
SPEAKER INSTALLATION  
The unique integral six foot mounting system incorporated into each AIM LCR3 speaker allows for a quick  
installation by following these easy steps:  
1
2
3
. Remove the grille. It may be necessary to push one or two of the mounting screws and its attached  
foot towards the baffle and against the inside surface of the grille to force the grille out of its retain-  
ing groove.  
. Attach the speaker cable (observing the proper polarity with your amplifier, + to + and – to –). Make  
sure the left channel of the amplifier is connected to the left speaker, and the right channel is con-  
nected to the right speaker.  
. Make sure the mounting feet are turned inward to clear the opening, and insert the speaker into the  
ceiling. Position the speaker into the hole. NOTE: The flange of the speaker is designed to flex and  
conform to any small imperfections in the ceiling’s surface. Tighten the six screws on the front of the  
baffle only enough to make the flange become snug against the ceiling. As you tighten the screws,  
the feet will automatically flip into an outward position (Figure 4), thereby clamping the drywall  
between the feet and the flange. CAUTION: Over tightening may warp the baffle, crack the ceiling,  
cause flange to distort, and make the grille difficult to install.  
4. Push the grille firmly into the slot in the speaker baffle.  
SPEAKER ADJUSTMENTS  
Pivoting Inner Baffle Adjustment  
FIGURE 6  
Push Tweeter Here  
Your AIM LCR3 Series speakers come from the factory with the inner baffles facing straight. This will result  
in the overall smoothest response. However, depending on your particular primary area, room acoustics,  
ceiling height, or personal preference, you may find the sound more pleasing by pointing the inner baffle  
in a particular direction. If additional sound is desired in the primary listening area, pivot the inner baffle  
towards that area; and if less sound is required, pivot the inner baffle away. Using both hands, push the  
ridged triangle areas located at each corner of the baffle to point it in the desired direction. (Figure 5).  
Pivoting Tweeter Adjustment  
Your AIM LCR3 Series speakers come from the factory with the tweeter facing straight out from the baffle.  
This will result in the overall smoothest response. However, depending on your particular primary area,  
room acoustics, ceiling height, or personal preference, you may find the sound more pleasing by point-  
ing the tweeters in a particular direction. If additional treble is desired in the primary listening area, point  
the tweeter towards that area; and if less treble is required, point the tweeter away. Push gently at the  
edge of the tweeter to point it in the desired direction. (Figure 6) CAUTION: Avoid touching tweeter dome  
as damage WILL occur on metal dome tweeters.  
For home theater use, we recommend the following tips:  
FIGURE 7  
If the speakers are being used as main front channels, the AIM LCR3 should be angled towards the  
listener.  
If the speakers are being used for rear surround channels, you may wish to pivot the AIM LCR3 away  
from the listener to achieve a more diffused sound.  
Treble Adjustment (AIM LCR3 Five & AIM LCR3 3):  
The switch labeled TREBLE allows for 6dB of tweeter adjustment. Your speakers were shipped with the  
Treble switch in the ”+” position, providing +3dB of treble. If you want less treble, slide the switch to the  
–” position and the tweeter will play –3dB of treble. (Figure 7)  
PAINTING THE SPEAKERS  
If you plan to paint your speakers, we recommend that it be done prior to installation. If you plan to paint your speakers sometime in the future, it  
is best to remove them by simply reversing the steps for “SPEAKER INSTALLATION” on page 2. If it is necessary to paint the speakers while they are  
still in the ceiling, the paint masks provided in the carton must be installed in place of the grille while the flange is being painted with the ceiling.  
The grilles can also be painted, however, great care should be taken not to clog the holes, as this will greatly reduce the sound quality of the  
speakers. SpeakerCraft recommends only light spray painting using 5 parts thinning agent to 1 part paint. Do not paint the grilles while they are  
attached to the speaker. If it is necessary to paint the under grille material, follow the same procedure used to paint the grilles.  
2

SpeakerCraft NOT FOUND AIM LCR3の説明書の他にも、あなたがSpeakerCraft NOT FOUND AIM LCR3とその問題を解決するのに役立つヘルプパネルを提供しています。何か質問がある場合は、以下のフォームから送信することができます。他のユーザーがここを訪問し、あなたのSpeakerCraft NOT FOUND AIM LCR3に関する問題解決を支援してくれるかもしれません。また、あなたがたどり着いた解決方法についてもご共有することをお忘れなく。うまく解決できた場合はSpeakerCraft NOT FOUND AIM LCR3に関する問題とその解決法についてこちらにご記入ください - きっと数多くのユーザーに役立つことでしょう。

デバイスの問題をお抱えですか?質問しましょう - 他のユーザーが助けてくれることでしょう

このデバイス/説明書のためのコメントはまだ投稿されていません。