取扱説明書JVC SP-XF10S

このページへお越しの方は、おそらくデバイスJVC SP-XF10Sに関する問題を抱えており、その説明書を必要としていることでしょう。お探しの説明書がお持ちのデバイスのそれであることを必ずご確認ください、お探しのJVC SP-XF10Sは、このデータベースではカテゴリースピーカーシステムに属します。 説明書JVC SP-XF10SはメーカーJVCの発行するものです - これは公式文書であるため、その内容に疑問がある場合はデバイスJVC SP-XF10Sの製造元に直接お問い合わせください。説明書JVC SP-XF10Sはオンラインで直接見たりコンピュータにダウンロードし保存したりすることができます。

Thank you for purchasing JVC speakers.  
Before you begin using them, please read the instructions carefully.  
English  
Speaker units  
Connections  
1
Speaker cord  
Front speaker (2)  
Center speaker (1)  
Surround speaker (2)  
Connect the speaker cords to the speaker terminals.  
2
Precautions for installation and daily use  
Press  
Insert  
Release  
Be sure to have the speakers installed on the wall by a qualified  
personnel to avoid unexpected damage from falling off the wall due to  
incorrect installation or weakness in the wall structure.  
Red (+)  
Care must be taken in selecting the location of installation on the wall.  
Injuries or damages may result if the speakers installed interfere with  
daily activities.  
Black ()  
The speakers are magnetically shielded to avoid color distortions on  
TVs if they are installed properly.  
SP-XF20C  
Rear)  
(
Copper  
Black striped  
When placing the speakers near a TV set, turn off the TVs main  
power switch or unplug it before installing the speakers.  
Then wait at least 30 minutes before turning on the TVs main power  
switch again. If there are still distortion, move the speakers further  
away from the TV.  
SP-XF20F  
(Rear)  
Press  
Red (+)  
Do not reproduce sounds at so high a volume that they are distorted;  
otherwise, the speakers may be damaged by internal heat buildup.  
When moving the speakers, do not pull the speaker cords; otherwise,  
the speakers may fall over, causing damage or injury.  
Black ()  
Connecting the speaker system to the amplifier  
Before connecting—  
Insert  
Turn off the power to the amplifier before connecting the speaker  
system; otherwise, the speakers may be damaged.  
Black striped  
The impedance of each speaker is 6 . Before connecting them to your  
amplifier, check the speaker impedance range of your amplifier. If the  
impedance of this speaker is out of the speaker impedance range  
indicated on the amplifier, you cannot connect this system to the amplifier.  
The maximum power handling capacity of the speakers are 100 W.  
Excessive input will result in abnormal noise and possible damage.  
Be sure to turn down the volume level to prevent unwanted noise  
before performing following operations:  
Copper  
Release  
SP-XF10S  
(Bottom)  
Turning on or off other components,  
Operating the amplifier,  
Tuning FM stations,  
Fast-forwarding a tape,  
Continuously reproducing high frequency oscillation or high pitch  
electronic sounds,  
Black striped  
Copper  
Through the hole  
Connecting or disconnecting a microphone.  
Connecting the speakers to the amplifier.  
When using a microphone, do not aim it at the speakers or use it near  
the speakers; otherwise, the howling which occurs may damage the  
speakers.  
Before replacing the cartridge, always turn off the power to the  
turntable; otherwise, the clicking noise may damage the speakers.  
3
Front left  
Front right  
Center  
Amplifier  
Subwoofer  
Specifications  
Type (magnetically-shielded type):  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
2-way 3-speaker Bass-reflex type  
1-way Bass-reflex type  
Speaker units:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
Power handling capacity/Impedance: 100 W/6 Ω  
Frequency range:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
Sound pressure level:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
Dimensions (W ×H ×D): SP-XF20F: 84 mm ×211 mm ×88 mm  
SP-XF20C: 209 mm ×85 mm ×92 mm  
Surround left  
Surround right  
5.5 cm cone (×2), 3.0 cm dome  
8.0 cm cone  
Connect the speakers to the speaker terminals of the amplifier  
with the speaker cords by referring to the diagram below.  
Make sure to match the polarity (ªand ·) when connecting  
the speaker cords.  
90 Hz to 40 000 Hz  
80 Hz to 20 000 Hz  
The diagram below is an example of a typical connection.  
FRONT LEFT  
CENTER  
81 dB/Wm  
75 dB/Wm  
FRONT RIGHT  
FRONT CENTER SURROUND SURROUND  
BACK  
SPEAKERS  
RIGHT LEFT  
RIGHT  
LEFT  
Recommended to use  
SP-SB100 (optionally  
purchased).  
SP-XF10S: 111.5 mm ×139 mm ×106.5 mm  
0.87 kg each  
0.52 kg each  
4 m (×3); 10 m (×2)  
Mass:  
SP-XF20F/SP-XF20C:  
SP-XF10S:  
SURROUND RIGHT  
SURROUND LEFT  
Accessories: Speaker cords:  
Design and specifications are subject to change without notice.  
3 –  
EN02-03_SP-XF20[E]f.p65  
3
31/3/04, 12:54 PM  

JVC SP-XF10Sの説明書の他にも、あなたがJVC SP-XF10Sとその問題を解決するのに役立つヘルプパネルを提供しています。何か質問がある場合は、以下のフォームから送信することができます。他のユーザーがここを訪問し、あなたのJVC SP-XF10Sに関する問題解決を支援してくれるかもしれません。また、あなたがたどり着いた解決方法についてもご共有することをお忘れなく。うまく解決できた場合はJVC SP-XF10Sに関する問題とその解決法についてこちらにご記入ください - きっと数多くのユーザーに役立つことでしょう。

デバイスの問題をお抱えですか?質問しましょう - 他のユーザーが助けてくれることでしょう

このデバイス/説明書のためのコメントはまだ投稿されていません。