Handleiding Fetco Home Decor Water Dispenser HWB-2000

Als u deze pagina heeft gevonden, heeft u waarschijnlijk een probleem en heeft u waarschaijnelijk de danleiding voor het apparaat Fetco Home Decor Water Dispenser HWB-2000 nodig. Controleer dat het een handleiding is voor het apparaat dat u zoekt. In onze databank Fetco Home Decor Water Dispenser HWB-2000 behoort het tot de categorie Waterdispenser. De handleiding Fetco Home Decor Water Dispenser HWB-2000 is afkomstig van de fabrikant, het bedrijf Fetco Home Decor - het is een officieel document, en als u twijfelt over de inhoud, neem dan direct contact op met de fabrikant van het apparaat Fetco Home Decor Water Dispenser HWB-2000. De handleiding Fetco Home Decor Water Dispenser HWB-2000 kunt u direct online bekijken of op te slaan op uw computer.

HWB-2000 Series  
Hot Water Dispensers  
FOOD EQUIPMENT TECHNOLOGIES COMPANY  
6
40 Heathrow Drive Lincolnshire IL 60069 USA  
3
Phone: (800) 338-2699 (847) 719-3000 Fax: (847) 821-1178  
E-mail: techsupport@fetco.com Internet: http://www.fetco.com  
Installation  
For Qualified Service Technicians Only)  
(
Keys To A Successful Installation  
Electrical: All FETCO dispensers require NEUTRAL. Ground is not an acceptable substitute. Installation  
without neutral may cause damage to the electronic components.  
The power connection to L1 on the terminal block must be at least 105 volts. Less than 105 volts will cause  
erratic behavior.  
The power switch has a built-in circuit breaker. To reset it, turn to the “off” position, and then back to the “on”  
position.  
The wiring diagram for the dispenser is located on the inside of the cover.  
Plumbing: This equipment is to be installed to comply with the applicable federal, state, or local plumbing codes.  
The water line must be flushed thoroughly prior to connecting it to the dispenser to prevent debris from  
contaminating the machine. An in-line water filter is strongly recommended.  
Verify that the water line will provide at least 2 gallons per minute before connecting it to the dispenser.  
General: Utilize a qualified beverage equipment service technician for installation.  
Do not adjust the thermostat settings unless absolutely necessary. They are set at the factory for optimum  
performance.  
Installation Check List  
The installation must comply with applicable federal, state, and local codes having jurisdiction at your location. Check  
with your local inspectors to determine what codes will apply to the installation and operation of FETCO products.  
1
.
.
Verify that the actual voltage at the electrical service connection is compatible with the specifications on the  
dispenser’s serial number plate. Make sure the electrical service includes neutral. Ensure at this time that the  
circuit breaker to the dispenser and the power switch on the dispenser are in the off position  
The temperature and the water tank fill level are pre-set at the factory. There is no need to turn off the heaters  
during the installation process. The heaters are disabled by the liquid level control board until water is sensed.  
The heating process will start automatically when the tank has filled with water  
2
3
4
.
.
Place the dispenser on a suitable counter or stand.  
When the dispenser is in position for use, level the dispenser front to back as well as side to side by adjusting  
the legs.  
5
6
. Remove the cover.  
. Water connection:  
Water inlet is a 3/8 inch compression fitting on HWB-25, 1/4 inch compression fitting on all other models.  
The dispenser can be connected to a cold or hot water line. Cold water is preferred for best flavor, but hot  
water will allow for faster recovery times. Use of an in-line water filter is strongly recommended.  
Install a water shut off valve near the dispenser to facilitate service. If an in-line water filter is used, it should  
be installed after the water shut off valve and in a position to facilitate filter replacement.  
Flush the water supply line and filter before connecting it to the dispenser.  
Verify that the water line will provide at least 2 gallons per minute and that the water pressure is between 20  
and 75 psig.  
Use a wrench on the factory fitting when connecting the incoming water line. This will reduce stress on the  
internal connections and reduce the possibility of leaks developing after the installation has been completed.  
7
. Vent tube connection:  

Naast de handleiding Fetco Home Decor Water Dispenser HWB-2000, bieden wij ook hulp panel die u zal helpen om uw problemen op te lossen met Fetco Home Decor Water Dispenser HWB-2000. Als u vragen heeft, kunt u ze in het onderstaande formulier invullen. Andere gebruikers zullen ze zien en kunnen u helpen om uw probleem op te lossen met Fetco Home Decor Water Dispenser HWB-2000. Vergeet niet dat u ook de oplossing kunt delen. Als u uzelf het probleem heeft opgelost, plaats hier een beschrijving en uw oplossing met Fetco Home Decor Water Dispenser HWB-2000 - u zal zeker de vele gebruikers helpen

Problemen met het apparaat? Stel een vraag - onze gebruikers kunnen helpen

Nog niemand heeft een commentaar voor deze machin/handleiding toegevoegd.