Handleiding Skil 1677M

Als u deze pagina heeft gevonden, heeft u waarschijnlijk een probleem en heeft u waarschaijnelijk de danleiding voor het apparaat Skil 1677M nodig. Controleer dat het een handleiding is voor het apparaat dat u zoekt. In onze databank Skil 1677M behoort het tot de categorie Zaag. De handleiding Skil 1677M is afkomstig van de fabrikant, het bedrijf Skil - het is een officieel document, en als u twijfelt over de inhoud, neem dan direct contact op met de fabrikant van het apparaat Skil 1677M. De handleiding Skil 1677M kunt u direct online bekijken of op te slaan op uw computer.

BM 1619X01743 08-06 8/17/06 8:48 AM Page 10  
SWITCH  
forward pressure. Do not overload motor.  
When starting the tool, Disconnect plug from power source and clean  
WARNING  
hold it with both hands. dust from air vents frequently. Metal cutting is  
!
The torque from the motor can cause the tool done at full depth.  
to twist.  
Clean guards frequently to  
WARNING  
assure a rapid return of  
!
To turn tool “ON”, squeeze the trigger switch.  
To turn the tool “OFF”, release the trigger lower guard. The lower guard may become  
switch, which is spring loaded and will return sluggish when cutting masonry materials.  
to the off position automatically.  
Abrasive Cut Off Wheels  
WARNING  
must have a maximum  
!
Your saw should be running at full speed  
BEFORE starting the cut, and turned off only safe operating speed greater than the “no  
AFTER completing the cut. To increase switch load RPM” marked on the tool’s  
life, do not turn switch on and off while cutting.  
nameplate. Wheels running over the rated  
speed can fly apart and cause injury.  
GENERAL CUTS  
Always hold the saw handle with one hand  
and the auxiliary handle or housing with the  
other.  
Do not use the abrasive  
WARNING  
cut off wheel near  
!
flammable materials. Sparks from the  
wheel could ignite these materials.  
Always be sure either hand  
WARNING  
does not interfere with the  
!
This machine is not  
WARNING  
intended to be used with  
!
free movement of the lower guard.  
Wet Diamond Wheels. Using water or other  
liquid coolants with this machine may result  
in electrocution or shock. Use of Dry  
Diamond Wheels is acceptable.  
Maintain a firm grip and operate the switch  
with a decisive action. Never force the saw.  
Use light and continuous pressure.  
After completing a cut and  
the trigger has been  
!
WARNING  
POCKET CUTS  
Disconnect the plug from the power source  
before making adjustments. Set depth adjust-  
ment according to material to be cut. Tilt saw  
forward with cutting guide notch lined up with  
the line you’ve drawn. Raise the lower guard,  
using lift lever and hold the saw by the front and  
rear handles (Fig. 7).  
released, be aware of the necessary time it  
takes for the blade to come to a complete  
stop during coast down. Do not allow the  
saw to brush against your leg or side,  
since the lower guard is retractable, it  
could catch on your clothing and expose  
the blade. Be aware of the necessary blade  
exposures that exist in both the upper and  
lower guard areas.  
With the blade just clearing the material to be  
cut, start the motor. Gradually lower the back  
end of saw using the front end of the foot as the  
hinge point.  
When cutting is interrupted, to resume cutting:  
squeeze the trigger and allow the blade to  
reach full speed, re-enter the cut slowly and  
resume cutting.  
FIG. 7  
When cutting across the grain, the fibers of  
the wood have a tendency to tear and lift.  
Advancing the saw slowly minimizes this  
effect. For a finished cut, a cross cut blade or  
miter blade is recommended.  
LOWER  
GUARD  
LIFT LEVER  
CUTTING MASONRY/METAL  
This tool is not recommended for continuous  
and general usage with metal or masonry cut-  
off wheels. If you use your saw for cutting  
these materials, use the appropriate wheel for  
the material being cut.  
LINE  
GUIDE  
FOOT  
As blade starts cutting the  
WARNING  
material, release the lower  
!
When cutting masonry, do not cut a depth of  
more than 1/4 inch (6 mm). Make successive  
passes to achieve desired depth. Apply a light  
guard immediately. When the foot rests flat on  
the surface being cut, proceed cutting in forward  
direction to end of cut.  
-
10-  

Naast de handleiding Skil 1677M, bieden wij ook hulp panel die u zal helpen om uw problemen op te lossen met Skil 1677M. Als u vragen heeft, kunt u ze in het onderstaande formulier invullen. Andere gebruikers zullen ze zien en kunnen u helpen om uw probleem op te lossen met Skil 1677M. Vergeet niet dat u ook de oplossing kunt delen. Als u uzelf het probleem heeft opgelost, plaats hier een beschrijving en uw oplossing met Skil 1677M - u zal zeker de vele gebruikers helpen

Problemen met het apparaat? Stel een vraag - onze gebruikers kunnen helpen

Nog niemand heeft een commentaar voor deze machin/handleiding toegevoegd.