Handleiding Skil 1677M

Als u deze pagina heeft gevonden, heeft u waarschijnlijk een probleem en heeft u waarschaijnelijk de danleiding voor het apparaat Skil 1677M nodig. Controleer dat het een handleiding is voor het apparaat dat u zoekt. In onze databank Skil 1677M behoort het tot de categorie Zaag. De handleiding Skil 1677M is afkomstig van de fabrikant, het bedrijf Skil - het is een officieel document, en als u twijfelt over de inhoud, neem dan direct contact op met de fabrikant van het apparaat Skil 1677M. De handleiding Skil 1677M kunt u direct online bekijken of op te slaan op uw computer.

BM 1619X01743 08-06 8/17/06 8:48 AM Page 2  
Power Tool Safety Rules  
Read and understand all instructions. Failure to follow all instructions listed  
WARNING  
below, may result in electric shock, fire and/or serious personal injury.  
!
SAVE THESE INSTRUCTIONS  
Work Area  
Keep your work area clean and well lit.  
Cluttered benches and dark areas invite  
accidents.  
Do not abuse the cord. Never use the cord  
to carry the tools or pull the plug from an  
outlet. Keep cord away from heat, oil,  
sharp edges or moving parts. Replace  
damaged cords immediately. Damaged  
cords increase the risk of electric shock.  
Do not operate power tools in explosive  
atmospheres, such as in the presence of  
flammable liquids, gases, or dust. Power  
tools create sparks which may ignite the dust  
or fumes.  
When operating a power tool outside, use  
an outdoor extension cord marked "W-A"  
or "W." These cords are rated for outdoor  
use and reduce the risk of electric shock.  
Keep by-standers, children, and visitors Refer to “Recommended sizes of Extension  
away while operating a power tool. Cords” in the Accessory section of this  
Distractions can cause you to lose control.  
manual.  
Personal Safety  
Electrical Safety  
Stay alert, watch what you are doing and  
use common sense when operating a  
power tool. Do not use tool while tired or  
under the influence of drugs, alcohol, or  
medication. A moment of inattention while  
operating power tools may result in serious  
personal injury.  
Grounded tools must be plugged into an  
outlet properly installed and grounded in  
accordance with all codes and  
ordinances. Never remove the grounding  
prong or modify the plug in any way. Do  
not use any adaptor plugs. Check with a  
qualified electrician if you are in doubt as  
to whether the outlet is properly  
grounded. If the tools should electrically  
malfunction or break down, grounding  
provides a low resistance path to carry  
electricity away from the user. Improper  
grounding can shock, burn or electrocute.  
Grounded tools are equipped with three  
conductor cord and three prong type plugs.  
Before plugging in the tool be certain the  
outlet voltage supplied is within the voltage  
marked on the nameplate. Do not use “AC  
only” rated tools with a DC power supply.  
Dress properly. Do not wear loose  
clothing or jewelry. Contain long hair.  
Keep your hair, clothing, and gloves away  
from moving parts. Loose clothes, jewelry,  
or long hair can be caught in moving parts.  
Keep handles dry, clean and free from oil  
and grease.  
Avoid accidental starting. Be sure switch  
is “OFF” before plugging in. Carrying tools  
with your finger on the switch or plugging in  
tools that have the switch “ON” invites  
accidents.  
Avoid body contact with grounded  
surfaces such as pipes, radiators, ranges  
and refrigerators. There is an increased  
risk of electric shock if your body is  
grounded. If operating the power tool in  
Remove adjusting keys or wrenches  
before turning the tool “ON”. A wrench or  
a key that is left attached to a rotating part of  
the tool may result in personal injury.  
damp locations is unavoidable, a Ground Do not overreach. Keep proper footing  
Fault Circuit Interrupter must be used to and balance at all times. Proper footing  
supply the power to your tool. Electrician’s and balance enables better control of the tool  
rubber gloves and footwear will further in unexpected situations.  
enhance your personal safety.  
Use safety equipment. Always wear eye  
Don't expose power tools to rain or wet protection. Dust mask, non-skid safety  
conditions. Water entering a power tool will shoes, hard hat, or hearing protection must  
increase the risk of electric shock.  
be used for appropriate conditions.  
-
2-  

Naast de handleiding Skil 1677M, bieden wij ook hulp panel die u zal helpen om uw problemen op te lossen met Skil 1677M. Als u vragen heeft, kunt u ze in het onderstaande formulier invullen. Andere gebruikers zullen ze zien en kunnen u helpen om uw probleem op te lossen met Skil 1677M. Vergeet niet dat u ook de oplossing kunt delen. Als u uzelf het probleem heeft opgelost, plaats hier een beschrijving en uw oplossing met Skil 1677M - u zal zeker de vele gebruikers helpen

Problemen met het apparaat? Stel een vraag - onze gebruikers kunnen helpen

Nog niemand heeft een commentaar voor deze machin/handleiding toegevoegd.