Als u deze pagina heeft gevonden, heeft u waarschijnlijk een probleem en heeft u waarschaijnelijk de danleiding voor het apparaat Skil 1677M nodig. Controleer dat het een handleiding is voor het apparaat dat u zoekt. In onze databank Skil 1677M behoort het tot de categorie Zaag. De handleiding Skil 1677M is afkomstig van de fabrikant, het bedrijf Skil - het is een officieel document, en als u twijfelt over de inhoud, neem dan direct contact op met de fabrikant van het apparaat Skil 1677M. De handleiding Skil 1677M kunt u direct online bekijken of op te slaan op uw computer.

BM 1619X01743 08-06 8/17/06 8:48 AM Page 5  

Maintain a firm grip with both hands on the Blade depth and bevel adjusting locking  

saw and position your body and arm to knobs must be tight and secure before  

allow you to resist KICKBACK forces. making cut. If blade adjustment shifts while  

KICKBACK forces can be controlled by the cutting, it may cause binding and KICKBACK.  

operator, if proper precautions are taken.  

Using the saw with an excessive depth of cut  

setting increases loading on the unit and  

susceptibility to twisting of the blade in the kerf.  

It also increases the surface area of the blade  

available for pinching under conditions of kerf  

close down.  

When blade is binding, or when interrupting  

a cut for any reason, release the trigger and  

hold the saw motionless in the material until  

the blade comes to a complete stop. Never  

attempt to remove the saw from the work or  

pull the saw backward while the blade is in Use extra caution when making a “Pocket  

motion or KICKBACK may occur. Investigate Cut” into existing walls or other blind areas.  

and take corrective action to eliminate the cause The protruding blade may cut objects that can  

of blade binding. Wet lumber, green lumber or cause KICKBACK.  

pressure treated lumber require special  

Some dust created by  

! WARNING  

power sanding, sawing,  

grinding, drilling, and other construction  

activities contains chemicals known to  

attention during cutting operation to prevent  

KICKBACK. Avoid cutting nails. Inspect for and  

remove all nails from lumber before cutting.  

When restarting a saw in a workpiece, cause cancer, birth defects or other  

center the saw blade in the kerf and check reproductive harm. Some examples of  

that saw teeth are not engaged into the these chemicals are:  

material. If saw blade is binding, it may walk up  

•

•

Lead from lead-based paints,  

or KICKBACK from the workpiece as the saw is  

restarted.  

Crystalline silica from bricks and cement  

and other masonry products, and  

Support large panels to minimize the risk of  

blade pinching and KICKBACK. Large panels  

tend to sag under their own weight. Supports  

•

Arsenic and chromium from chemically-  

treated lumber.  

must be placed under the panel on both sides, Your risk from these exposures varies,  

near the line of cut and near the edge of the depending on how often you do this type of  

panel. See “Cutting Large Sheets” in this work. To reduce your exposure to these  

manual.  

chemicals: work in a well ventilated area, and  

work with approved safety equipment, such  

as those dust masks that are specially  

designed to filter out microscopic particles.  

Do not use dull or damaged blade.  

Unsharpened or improperly set blades produce  

narrow kerf causing excessive friction, blade  

binding and KICKBACK.  

-

5-  

• ← Previous
• Next page →

Naast de handleiding Skil 1677M, bieden wij ook hulp panel die u zal helpen om uw problemen op te lossen met Skil 1677M. Als u vragen heeft, kunt u ze in het onderstaande formulier invullen. Andere gebruikers zullen ze zien en kunnen u helpen om uw probleem op te lossen met Skil 1677M. Vergeet niet dat u ook de oplossing kunt delen. Als u uzelf het probleem heeft opgelost, plaats hier een beschrijving en uw oplossing met Skil 1677M - u zal zeker de vele gebruikers helpen