Als u deze pagina heeft gevonden, heeft u waarschijnlijk een probleem en heeft u waarschaijnelijk de danleiding voor het apparaat JBL LSR6328P nodig. Controleer dat het een handleiding is voor het apparaat dat u zoekt. In onze databank JBL LSR6328P behoort het tot de categorie Luidsprekersysteem. De handleiding JBL LSR6328P is afkomstig van de fabrikant, het bedrijf JBL - het is een officieel document, en als u twijfelt over de inhoud, neem dan direct contact op met de fabrikant van het apparaat JBL LSR6328P. De handleiding JBL LSR6328P kunt u direct online bekijken of op te slaan op uw computer.

Amplitude & Phase  

_SS_ysp_teme_: cifications:  

Frequency Response (+1, -1.5 dB): 50 Hz - 20 kHz  

Enclosure Resonance Frequency: 38 Hz  

Low Frequency Extension: User controls set to default  

-

3 dB: 46 Hz  

-

10 dB: 36 Hz  

Low-High Frequency Crossover: 1.7 kHz 6th-order acoustic Linkwitz-Riley  

Distortion, 96 dB SPL, 1 m:  

Mid-High Frequency (120 Hz - 20 kHz):  

2

nd Harmonic: <0.6%  

rd Harmonic: <0.5%  

Low Frequency (<120 Hz):  

nd Harmonic: <2%  

rd Harmonic: <1%  

3

2

3

Maximum SPL (80 Hz - 20 kHz): >108 dB SPL / 1m  

Maximum Peak SPL (80 Hz - 20 kHz): >111 dB SPL / 1m  

Signal Input: Neutrik “Combi” XLR-¼-in tip-ring-sleeve balanced or unbal-  

96 dB/1 m (Distortion raised 20 dB)  

anced positive voltage applied to XLR pin 2 (¼" tip) produces  

outward woofer motion  

Calibrated Input Sensitivity, XLR & ¼":  

4 dBu / +8 dBu: 96 dB SPL / 1 m  

10 dBV: 96 dB SPL / 1 m  

+

-

AC Input Voltage: 100 /240 VAC, 50/60 Hz (auto sensing)  

AC Input Connector: IEC  

Long-Term Maximum System Power: 220 watts (IEC265-8)  

Self-Generated Noise Level: <10 dBA / 1 m Tonal-artifact-free noise floor  

User Controls:  

2

nd  

rd  

3

High Frequency Control (2 kHz - 20 kHz): +1 dB, 0 dB, -1 dB  

Low Frequency Control (< 100 Hz): 0 dB, -2 dB  

Low Frequency Alignments: 36 dB/octave, 24 dB/octave (VLF protection off)  

Calibrated Input Sensitivity: -10 dBV, +4 dBu, +8 dBu  

Boundary Compensation Settings: 0, -1.5, -3.0, -4.5 dB  

Variable Input Attenuation: 0 dB to -13 dB  

RMC External Bypass: ¼" jack  

RMC Active Switch: In/Out  

RMC Frequency Adjust: 26 Hz - 96 Hz (10th octave, 18 centers)  

RMC Depth Adjust: 0 - 14 dB (cut only)  

102 dB/1 m (Distortion raised 20 dB)  

RMC Q Adjust: 1/20th to 1/2 octave, 21 steps  

Transducers:  

Low Frequency Model: 218F  

Diameter: 203 mm (8 in)  

®

Voice Coil: 38 mm (1.5 in) Differential Drive with dynamic braking coil  

Magnet Type: Ferrite, with integral heat sink  

Cone Type: Carbon fiber composite  

2nd  

Impedance: 2 ohms  

High Frequency Model: 053TiS  

Diameter: 25 mm (1 in) diaphragm  

Voice Coil: 25 mm (1 in)  

3rd  

Magnet Type: Ferrite, shielded  

Diaphragm Type: Damped titanium composite  

Other Features: Elliptical oblate spheroidal waveguide  

Impedance: 4 ohms  

Amplifier:  

Low Frequency:  

Topology: Class A-B, all discrete  

Notes:  

Sine Wave Power Rating: 250 watts (<0.1% THD into rated impedance)  

THD + N, ½Power: <0.05%  

All measurements unless otherwise stated made anechoically in a 4␲environment at 2  

meters, referenced to 1 meter by inverse square law.  

High Frequency:  

The reference measurement microphone position is located perpendicular to the cen-  

terline of the low and high frequency transducers at the point 55 mm (2.2 in) below  

the center of the high frequency diaphragm.  

Acoustic loading provided by the listening room increases maximum SPL capability  

and low frequency bass extension as compared to stated anechoic values.  

Topology: Class A-B, monolithic  

Sine Wave Power Rating: 120 watts (<0.1% THD into rated impedance)  

THD + N, ½Power: <0.05%  

Physical:  

Distortion measurements performed with the input voltage necessary to produce the  

stated A- weighted SPL at the stated measurement distance. Distortion figures refer to  

the maximum distortion measured in any 1/10th octave wide band in the stated fre-  

quency range.  

Finish: Smooth dark graphite  

Handles: 2 each, flush mounted on sides  

Mounting: 4 threaded mounting points conforming to industry standard  

square pattern, 127 x 70 mm (5 x 2.75 in) center to center. M6  

metric threads.  

Enclosure Volume (net): 28 liter (1 cu ft)  

Low Frequency Vent: Rear ported linear dynamics aperture (integrated with  

amplifier heat sink)  

JBL continually engages in research related to performance improvements. New mate-  

rials, production methods, and design refinements are introduced into existing prod-  

ucts without notice as a routine expression of that philosophy. For this reason, any  

current JBL product may differ in some respect from its published description, but will  

always equal or exceed the original design specification unless otherwise stated.  

Baffle Construction: Injection-molded structural ABS  

Enclosure Construction: 19 mm (¼in) MDF  

Net Weight: 17.7 kg (39 lb)  

Dimensions (HxWxD): 406 x 330 x 325 mm (16 x 13 x 12.8 in)  

Caution: Unsafe mounting or overhead suspension of any heavy load can result in serious injury and equipment  

damage. Mounting of speakers should be done by qualified persons in accordance with all applicable local safety  

and construction standards. Be certain to follow the instructions provided by the manufacturer of the mounting  

bracket. Before selecting a mounting bracket, be certain that it is capable of supporting the weight of the speaker  

to be mounted.  

• ← Previous
• Next page →

Naast de handleiding JBL LSR6328P, bieden wij ook hulp panel die u zal helpen om uw problemen op te lossen met JBL LSR6328P. Als u vragen heeft, kunt u ze in het onderstaande formulier invullen. Andere gebruikers zullen ze zien en kunnen u helpen om uw probleem op te lossen met JBL LSR6328P. Vergeet niet dat u ook de oplossing kunt delen. Als u uzelf het probleem heeft opgelost, plaats hier een beschrijving en uw oplossing met JBL LSR6328P - u zal zeker de vele gebruikers helpen