Handleiding Extron electronic WM EC F

Als u deze pagina heeft gevonden, heeft u waarschijnlijk een probleem en heeft u waarschaijnelijk de danleiding voor het apparaat Extron electronic WM EC F nodig. Controleer dat het een handleiding is voor het apparaat dat u zoekt. In onze databank Extron electronic WM EC F behoort het tot de categorie Stereo versterker. De handleiding Extron electronic WM EC F is afkomstig van de fabrikant, het bedrijf Extron electronic - het is een officieel document, en als u twijfelt over de inhoud, neem dan direct contact op met de fabrikant van het apparaat Extron electronic WM EC F. De handleiding Extron electronic WM EC F kunt u direct online bekijken of op te slaan op uw computer.

Controls and Installation, cont’d  
P/2 DA2 WM F wall mount installation  
P/2 DA2 WM EC F Euro Channel installation  
Once the input and output cables have been connected and the  
P/2 DA2 WM F has been successfully tested, the faceplate may  
be attached to the mounting bracket using the four supplied  
screws.  
Once the input and output cables have been connected and  
tested on the P/2 DA2 WM F EC, the distribution amplifier can  
be easily installed in the Euro Channel.  
EC  
P/2 DA2  
WM  
F
N
The center pole of the power input connector contains no  
conductor. Connect the conductors to the two outer  
poles only, exactly as shown here.  
IN1S1  
ID  
4
P
POWER  
RED NITOR  
ADSP  
TM  
AUTO  
BUFFE  
L
MO  
WITH  
AUDIO  
LOCA  
GAIN  
/
KING  
INPUT  
P
NI1T0Y05%0%  
E
A
U
Positive  
N/C  
Negative  
Audio (3.5 mm  
Captive Screw  
Connector)  
Power (3.5 mm  
Captive Screw  
Connector)  
Rear Cover Screws  
Do not remove unless faceplate  
is removed from wall.  
WM F EC  
P/2 DA2  
ID  
4
P
IN1S1  
POWER  
UFFEREMDONITOR  
B
LOCAL  
ADSP  
TM  
AUTO  
WITH  
AUDIO  
GAIN  
/
KING  
INPUT  
Euro Channel  
P
NI1T0Y05%0%  
E
A
U
AUTOPOWER  
AUDIO  
1
00%  
UNITY  
INPUT  
5
0%  
GAIN/PEAKING  
BUFFERED  
ID PIN  
4
LOCAL MONITOR  
ID PIN 11  
P/2  
D
A2 WM  
F
EuroChannelinstallation  
VGA Connector  
Setting the DIP switches  
Two sliding-type DIP switches can be found on the faceplate of  
the P/2 DA2 WM F/EC F.  
1
2
To set the sliding-type DIP switches, slide the switch to  
the on/closed or off/open position.  
The two DIP switches provide proper ID bit termination for a  
laptop computer that is not attached to a local monitor.  
ID Pin 4 & ID Pin 11  
ON Set both pins to On if you are using the P/2 DA2  
ID PIN 4  
ID PIN 11  
WM F/EC F with a laptop computer that is not  
attached to a local monitor.  
OFF Set both pins to Off if you are attaching a local  
monitor to the  
P/2 DA2 WM F/EC F.  
Wall mounting the P/2 DA2 WM F  
2
-14  
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation  
P/2 DA2 WM/EC/D/AAP Series • Controls and Installation  
2-15  

Naast de handleiding Extron electronic WM EC F, bieden wij ook hulp panel die u zal helpen om uw problemen op te lossen met Extron electronic WM EC F. Als u vragen heeft, kunt u ze in het onderstaande formulier invullen. Andere gebruikers zullen ze zien en kunnen u helpen om uw probleem op te lossen met Extron electronic WM EC F. Vergeet niet dat u ook de oplossing kunt delen. Als u uzelf het probleem heeft opgelost, plaats hier een beschrijving en uw oplossing met Extron electronic WM EC F - u zal zeker de vele gebruikers helpen

Problemen met het apparaat? Stel een vraag - onze gebruikers kunnen helpen

Nog niemand heeft een commentaar voor deze machin/handleiding toegevoegd.