User manual CyberPower CP1000D

If you found this page, you probably have a problem and you need a user manual for the device CyberPower CP1000D. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database CyberPower CP1000D it belongs to the category Power Supply. A user manualCyberPower CP1000D is taken from the manufacturer, a CyberPower company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device CyberPower CP1000D directly. You can view the user manualCyberPower CP1000D directly online or save and store it on your computer.

Note: Only one of these two ports can be used to communicate with your computer at one time.  
Note: To install PowerPanel™ Personal Edition Software the computer will need MicrosoftR Internet Explore 5.0 or higher installed.  
3. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on  
all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and the name of the power utility  
DEFINITIONS FOR ILLUMINATED LED INDICATORS  
Note: If using the Serial Port please read the directions to configure the MicrosoftR UPS service on our website  
supplier for the location of the Connected Equipment and Request  
a Claim Number.  
4.  
Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the damage  
http://www.cyberpowersystems.com/ups_service.asp  
tech@cyberpowersystems.com  
.
If you need  
a
serial cable please contact CyberPower technical support at  
to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the shipping label or include  
it with the product. Initial Customer shall prepay all shipping costs, must pay the cost of the repair estimate, and is responsible for  
packaging and shipment.  
CP900D / CP1000D /  
CP1200D / CP1285D / CP1500D  
User’s Manual  
12 Coax/Cable/DSS Surge Protection  
CONDITION  
Using  
Ove  
Wiring  
Fault  
The Coax/Cable/DSS surge protection ports will protect any cable modem, CATV converter, or DSS receiver.  
Power ON  
Batteryꢀ  
AVR  
Load  
Alarm  
CyberPower’s Duties.  
1
3
Outlets Designed for AC Adapters  
On  
Off  
On  
Off  
Off  
Off  
Off  
Off  
Normal  
sCtyabteemrP  
o
w
t
earndwrilelpinasirp  
e
c
sttaensdtimeaxtaemfoinrethto  
h
s
e
ePiteromd(usc)t).aYnodu mthuesitteremtu(srn) tohfeCporondnueccttefodr Einqsupiepcmtieonnt. (or at CyberPower's election, your written  
The unit has four outlets spaced to allow AC power adapter blocks to be plugged into the UPS without blocking adjacent outlets.  
en  
c
o
K01-0000003-00  
On  
On  
Off  
Off  
On/Off  
Two  
Beeps  
Utility Failure- The UPS is providing power to battery  
power supplied outlets.  
If the damage to Connected Equipment is covered by the Connected Equipment Guarantee, CyberPower will (in addition to Limited  
Warranty remedies for the CyberPower Product itself) repair (or pay the costs of repair) or replace the Connected Equipment or, at the  
option of CyberPower, as permitted by law, pay to the Initial Customer the "Agreed Damage Amount" (up to the aggregate limits stated  
below) for all item(s) of Initial Customer's Connected Equipment. The "Agreed Damage Amount" for all items of Initial Customer's Connected  
bEeqluoiwpm: ent shall be the lesser of the amount determined under Clause (1) or (2) below, reduced by any amounts described in Clause (3)  
REPLACING THE BATTERY  
IMPORTANT SAFETY WARNINGS  
CAUTION! Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Service the battery under the  
supervision of personnel knowledgeable of batteries and their precautions.  
On  
Off  
Off  
On  
On/Off  
On/Off  
BReaeppids  
Utility Failure- The UPS is providing battery power. Rapid  
beeps indicate the unit will run out of power shortly.  
(SAVE THESE INSTRUCTIONS)  
CAUTION! Use only the specified type of battery. See your dealer for replacement batteries.  
1.  
The fair market value of the Connected Equipment as established by the lower of (a) the price list of Orion Blue Book on the date of  
occurrence (or if such price list is no longer published, published or announced price list reasonably selected by CyberPower), or (b) the  
average price the same or similar items are being sold for on  
E-bay, or (c) the lowest price the same or similar items can be purchased for in the United States; or  
2. The aggregate ceiling amount for all Connected Equipment: CyberPower CP900D $300,000.00. CP1000D  
375,000.00. CP1285D $375,000.00. CP1500D $500,000.00.  
This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the  
CAUTION! The battery may present  
a
risk of electrical shock. Do not dispose of battery in  
a
fire as it may explode. Follow all local  
System Overload- Occurs when connected equipment  
exceeds the rating of unit. Turn the UPS off, unplug at  
a
unit. Read this manual thoroughly before attempting to unpack, install, or operate your UPS.  
ordinances regarding proper disposal of batteries. Almost any retailer that sells lead-acid batteries collects used batteries for recycling, as  
required by most state laws.  
On  
On  
Off  
Off  
Long  
Beep  
CAUTION! To prevent the risk of fire or electric shock, install in  
a
temperature and humidity controlled indoor area free of conductive  
lceira  
s
c
utitobnreeapkiecreaonfdetquurniptmheenutn, iwt oanit.10 seconds, reset the  
e
contaminants. (Please see specifications for acceptable temperature and humidity range).  
CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. No user serviceable parts inside  
except for battery.  
CAUTION! Do not open or mutilate the batteries. Released electrolyte is harmful to skin and eyes and may be toxic.  
-
- $300,000.00. CP1200D -  
$
-
-
CAUTION!  
A
battery can present  
a
high risk of short circuit current and electrical shock. Take the following precautions before replacing the  
Battery Overload- Occurs when connected equipment  
exceeds the rating of battery outlets of the unit. Turn the  
UPS off, unplug at least one piece of equipment from  
baantdtetruyrnouthtleetusn, iwt oanit.10 seconds, reset the circuit breaker  
3. The amount(s) of all payment you have or are entitled to receive from insurance, other warranties, extended warranties, or from other  
sources or persons for the Connected Equipment or damage to such equipment so that CyberPower’s maximum liability shall be reduced to  
reflect all such other payments or sources of recovery  
If CyberPower replaces the connected equipment or pays to the Initial Customer the Agreed Damage Amount, the Initial Customer shall  
transfer ownership of all item(s) to CyberPower without warranty by the Initial Customer, but free of lien or other interest.  
battery:  
BLoenegp  
CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.  
CAUTION! UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not  
grounded. If you need to de-energize this equipment, turn off and unplug the unit.  
1.Remove all watches, rings or other metal objects.  
Off  
On  
On/Off  
2.Only use tools with insulated handles.  
3.Do not lay tools or metal parts on top of battery or any terminals.  
4.Wear rubber gloves and boots.  
CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing  
a
CONDITIONS COMMON TO THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE  
The Limited Warranty and the Connected Equipment Guarantee are the only and the exclusive express warranty of CyberPower with  
respect to the Product. This exclusion of other express warranties applies to written and oral express warranties.  
AVR Mode-Max. boost 12% of input voltage for output  
regulation while input voltage is from 17% to 26% under  
nominal.  
computer component.  
5.Determine if the battery is inadvertently grounded. If grounded, remove the source of ground. CONTACT WITH GROUNDED BATTERY  
CAN RESULT IN ELECTRICAL SHOCK!  
On  
Off  
On  
Off  
Off  
On/Off  
On  
Off  
CAUTION! To reduce the risk of fire, connected only to  
accordance with the national Code, ANSI / NFPA 70.  
a circuit provided with 20 amperes maximum branch circuit over current protection in  
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical  
applications. DO NOT use in any circumstance that would affect operation or safety of any life support equipment or with any medical  
applications or patient care.  
TO REPLACE THE BATTERY  
1. Turn off and unplug all connected equipment.  
EwliethcttrhiceaAl WC ioriuntgleFt asuuclth- Tahsisbain  
reversed wiring. User is advised to disconnect all  
electrical equipment from the outlet and have an  
electrician check the outlet to insure proper wiring.  
dgicraotuensda, mwiirsisnigngprgorboluenmd, or  
d
LIMITATION: THE LIMITED WARRANTY AND THE CONNECTED EQUIPMENT GUARANTEE DOES NOT COVER  
The Limited Warranty and the Connected Equipment Guarantee are intended to exclusive rights and remedies and replace any other rights,  
to the extent allowed by law.  
1. As to the CyberPower Product, the limited warranty does not cover or apply to: misuse, modification, operation or storage outside  
environmental limits for the Products, in transit, in shipment, or in storage, damage or deterioration, improper operation or maintenance, or  
use with items or equipment not designed or intended for use with the product.  
On/Off  
On/Off  
On/Off  
None  
2. Turn the UPS off and unplug it from the AC power source.  
3. Turn the UPS upside down.  
DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium.  
Condensation from the aquarium can cause the unit to short out.  
4. Remove the retaining screw.  
2. As to Connected Equipment, the Connected Equipment Guarantee covers only damage within the specific terms of the Connected  
Equipment Guarantee to Connected Equipment (and only up to the applicable aggregate ceiling amount).  
DO NOT USE WITH LASER PRINTERS! The power demands of these devices will overload and possibly damage the unit.  
5. Slide the battery compartment cover (front panel) completely off of the unit.  
6
7
8
.
.
.
Remove the batteries from the compartment.  
Limited Warranty and Connected Equipment Guarantee  
3. The Connected Equipment Guarantee does not cover damage to Connected Equipment or apply if the Product has been operated in a  
failure mode or not in compliance with CyberPower operating instructions and manuals, or if the Connected Equipment has been operated  
in failure mode or not in compliance with the instructions and manuals of its manufacturer/vendor.  
Disconnect the battery wires from the batteries.  
Install the replacement batteries by connecting the red wire and black wire to the same color  
wires from the battery pack.  
a
INSTALLING YOUR UPS SYSTEM  
Limited Warranty and Connected Equipment Guarantee from Cyber Power Systems (USA), Inc. (for ease of reading, referred to as  
"CyberPower"). The Limited Warranty and the Connected Equipment Guarantee are intended to be the original end-user's exclusive rights  
and remedies. The Limited Warranty and the Connected Equipment are separate, all though they are related.  
The Limited Warranty and the Connected Equipment Guarantee Do Not Apply Unless The Initial Customer:  
1. Has properly connected the Product and the Connected Equipment to properly wired and grounded outlets (including compliance with  
electrical and safety codes of the most current electrical code (ANS/NFPA 70), without the use of any adapters, extension cords or other  
connectors.  
2. Has provided a suitable and proper environment for use and installation of the Product and Connected Equipment.  
3. Has properly installed and operated the CyberPower Product and Connected equipment.  
UNPACKING  
Inspect the UPS upon receipt. The box should contain the following:  
9.  
Put the batteries back into the compartment.  
10. Slide back the battery compartment cover and tighten the retaining screw.  
11. Recharge the UPS for 8-16 hours to fully charge the battery.  
(1) UPS unit; (1) User’s manual; (1) PowerPanel™ Personal Edition software CD; (1) USB device cable; (1) Telephone cable; (1) Warranty  
Limited Warranty. The original end user (referred to as the "Initial Customer") receives an express limited warranty (referred to as the  
registration card; (1) Coaxial Cable  
REMINDER: Batteries are consider HAZARDOUS WASTE and must be disposed of properly. Almost any retailer that sells lead-acid  
"
Product"). The Limited Warranty is for the Product itself. The terms of the Limited Warranty are explained below.  
/
CP1000D  
/
CP1200D  
/
CP1285D  
/
CP1500D purchased from CyberPower (referred to as the  
4. Has operated the Product at all times within the limitations on the Product’s VA capacity as stated in this User Manual.  
batteries collects used batteries for recycling, as required by most state laws.  
OVERVIEW  
Connected Equipment Guarantee. CyberPower also provides the Initial Customer with protection in the event that the Product is not free  
from defects in materials and workmanship, and certain equipment connected to the Product is damaged (the "Connected Equipment  
Guarantee"). The Connected Equipment Guarantee protects the Initial Customer for damage to equipment plugged into the Product. The  
terms of the Connected Equipment Guarantee are explained below.  
CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following:  
The CP900D  
inconsistent utility power. The CP900D  
90/890/1080/1080/1500 Joules of surge protection, and provide battery backup during power outages.  
The CP900D CP1000D CP1200D CP1285D CP1500D ensure consistent power to your computer  
system and include software that will automatically save your open files and shutdown your computer  
system during utility power loss.  
/
CP1000D  
/
CP1200D  
/
CP1285D  
/
CP1500D provide automatic voltage regulation for  
1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.  
2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and code-compliant 120  
volt power lines in the United States and Canada; transients, surges or spikes on standard telephone land lines, PBX telephone equipment  
lines or Base 10T Ethernet lines, when properly installed and connected. (This exclusion applies, for example, to fluctuations in data  
transmission or reception, by CATV or RF transmission or fluctuations, or by transients in such transmission.  
3. Damage from any circumstance described as excluded above with respect to the product.  
/
CP1000D  
/
CP1200D CP1285D CP1500D features  
/
/
Automatic Voltage Regulators  
increase low or decrease high voltage to computer  
safe 110/120 volts. The AVR automatically provides  
battery back-up power if line voltage drops below 90  
volts or exceeds 140 volts.  
TROUBLE SHOOTING  
8
/
/
/
/
Problem  
Possible Cause  
Solution  
The Limited Warranty and the Connected Equipment Guarantee are subject to the terms set forth below. Additionally, State or Provincial law  
may adjust the terms of the Limited Warranty or the Connected Equipment Guarantee or the State or Province may impose additional  
obligations, or additional "implied warranties." To the extent necessary to comply with those laws, the terms of the Limited Warranty and the  
Connected Equipment Guarantee should be read to adjust to those requirements only to the extent necessary to comply with such local law.  
AVR  
Full-time surge protection outlets  
Turn the UPS off and unplug at least one piece of equipment.  
Wait 10 seconds, reset the circuit breaker by depressing the  
button, and then turn the UPS on.  
4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the product or  
the Connected Equipment.  
a
IN  
C
IL  
O
IT  
N
Y
SPIS  
O
T
WENETR  
CSAO  
N
SIP  
S
OTWEN  
T
U
T
F
E
E
R
Circuit breaker button is projecting  
from the side of the unit.  
overload.  
AUTOMATIC VOLTAGE REGULATOR?  
The CP900D CP1000D CP1200D CP1285D CP1500D stabilize inconsistent utility power. The incoming utility  
power may be damaging to important data files, but with Automatic Voltage Regulation, the computer will not experience  
damaging voltage levels. An Automatic Voltage Regulator automatically increases low or decreases high voltage to consistent,  
If you are an Initial Customer, you are asked to read the following terms and conditions carefully before using the Product. By using the  
Exclusion of Consequential and Other Damages.  
/
/
/
/
The UPS does not perform  
expected runtime.  
Battery not fully charged.  
Recharge the battery by leaving the UPS plugged in.  
Product you consent to be bound by and become  
a
party to the Limited Warranty and Connected Equipment Guarantee. If you do not agree  
The sole and exclusive remedies of the Initial Customer are those provided by the Limited Warranty and Connected Equipment Guarantee.  
CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee. CyberPower  
excludes any liability for direct, indirect, special, incidental or consequential damages, whether for damage to or loss of property [EXCEPT  
FOR (AND ONLY FOR) the specific limited agreement of CYBERPOWER to provide certain warranty benefits regarding "Connected  
Equipment" under the "CYBERPOWER Connected Equipment Guarantee"], loss of profits, business interruption, or loss of information or  
data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above  
limitation may not apply to you.  
Battery is slightly worn out.ꢀ  
Contact CyberPower Systems about replacement batteries at  
tech@cyberpowersystems.com  
to the terms and conditions of the Limited Warranty and Connected Equipment Guarantee, you should return the Product for a full refund  
prior to using it.  
REGISTRATION  
CyberPower requests that you complete and return the Warranty Registration Card enclosed with the Product or register the Product at its  
website (www.cyberpowersystems.com) to establish that you are the Initial Customer of the Product, and therefore entitled coverage under  
the Limited Warranty and the Connected Equipment Guarantee. (Registration is not required for Limited Warranty coverage, but note if you  
a
computer safe 110v/120v. The unit’s powerful sealed lead-acid batteries will provide power only if the incoming voltage drops below 90v or  
increases above 140v.  
The on/off switch is designed  
tourpnrinegveitnot fdfa  
mndag  
en.by rapidly  
Turn the UPS off. Wait 10 seconds and then turn the UPS on.  
a
o
HARDWARE INSTALLATION GUIDE  
The unit is not connected to an  
AC outlet.  
The unit must be connected to  
a
110/120v 60Hz outlet.  
do not complete  
Warranty.)  
a
registration card you will be required to provide proof of purchase, as described below, to have the benefits of this Limited  
DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT OR OTHER HIGH RISK ACTIVITIES.  
1.ꢀYour new UPS may be used immediately upon receipt. However, recharging the batteries for at least 16 hours is recommended to insure  
The UPS will not turn on.  
LIMITED WARRANTY  
CyberPower warrants to you, the Initial Purchaser, that the Product will be free from defects in material and workmanship for three years  
from the date of original purchase, subject to the terms of this Limited Warranty.  
CyberPower does not sell the Products for use in high-risk activities. The Product is not designed or intended for use in hazardous  
environments requiring fail-safe performance, including the operation of nuclear facilities, aircraft navigation or communication systems, air  
traffic control, weapons systems, life support or medical applications or for use in any circumstance in which the failure of the Product could  
lead directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical or life  
support device (collectively, "High Risk Activities"). CyberPower expressly disclaims any express or implied warranty of fitness for High Risk  
Activities. CyberPower does not authorize use of any of its products use in any High Risk Activities.  
that the battery’s maximum charge capacity is achieved. A loss of charge may occur during shipping and storage. To recharge the  
The battery is worn out.  
Mechanical problem.  
Contact CyberPower Systems about replacement batteries at  
tech@cyberpowersystems.com  
batteries, simply leave the unit plugged into an AC outlet. The unit will charge in both the ON as well as the OFF position.  
.ꢀWith the UPS unit off and unplugged, connect your computer, monitor, and any externally powered data storage device (Zip drive, Jazz  
drive, Tape drive, etc…) into the battery power supplied outlets. Plug your peripheral equipment (printer, scanner, speakers) into the full-  
2
Contact CyberPower Systems at  
tech@cyberpowersystems.com  
Any Implied Warranty of Merchantability or for Fitness for a Particular Purpose, if applicable to the Product, is limited in duration to the  
period of ownership by the Initial Customer. This provision shall NOT create any Implied Warranty or Merchantability or of Fitness for  
a
time surge protection outlets. DO NOT plug  
device into the UPS. The power demands of these devices will overload and possibly damage the unit.  
.ꢀTo surge protect network connection, connect network cable from the wall jack outlet to the IN jack of the UPS. Then connect  
network cable from the OUT jack on the UPS to the network device.  
.ꢀPlug the UPS into pole, wire grounding receptacle (wall outlet). Make sure the wall branch outlet is protected by  
a
laser printer, paper shredder, copier, space heater, vacuum or other large electrical  
The USB cable is not  
connected.  
Connect the USB cable to the UPS unit and an open USB port  
on the back of the computer. You must use the cable that came  
with the unit.  
Particular Purpose that would not otherwise apply to the Product. NOTE: Some States do not allow limitations on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
ANY SUCH USE IS IMPROPER AND IS A MISUSE OF CYBERPOWER PRODUCTS.  
The Limited Warranty and the Connected Equipment Guarantee are governed by the laws of the United States and the State of Minnesota,  
without reference to conflict of law principles. The application of the United Nations Convention of Contracts for the International Sale of  
Goods is expressly excluded.  
Contact Information: CyberPower's address is 5555 12th Ave East, Suite 110, Shakopee, MN 55379 and its phone number is (952) 403-  
9500 or Toll-free: (877) 297-6937. CyberPower is the warrantor under this Limited Warranty. You may also contact CyberPower on the  
Internet at www.cyberpowersystems.com.  
3
a
a
a
To be covered you must still be the owner of the Product at the time of the failure that results in the claim made under this Limited Warranty.  
The USB cable is connected  
to the wrong port.  
Check the back of the computer for an additional USB port.  
Move the cable to this port.  
4
a
2
3
a
PisoinwaecrPtiva  
e
ne(al™ll icP  
e
o
nrssoanrealgEradyit)io.  
n
Exclusive Remedies Under Limited Warranty.  
fuse or circuit breaker and does not service equipment with large electrical demands (e.g. refrigerator, copier, etc…).  
The warranty prohibits the use of extension cords, outlet strips, and surge strips.  
The unit is not providing  
battery power.  
Shutdown your computer and turn the UPS off. Wait 10  
seconds and turn the UPS back on. This should reset the unit.  
Your exclusive remedy and CyberPower's' sole obligations are as follows for the Product:  
If (a) the CyberPower Product you purchased and still own is defective in material or workmanship under this Limited Warranty or any  
applicable warranty imposed by law, and  
IN  
OUT  
5
.ꢀPress the power switch to turn the unit on. The power on indicator light will illuminate and the unit will “beep” once.  
Additional troubleshooting information can be found at  
www.cyberpowersystems.com/support.htm  
(b) all Limited Warranty requirements have been met, CyberPower will repair or replace the  
Product if it proves to be defective in material or workmanship during the Warranty Period.  
FCC Notice  
This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in residential installation. This equipment  
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause  
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient or relocate the receiving  
antenna. (2) Increase the separation between the equipment and receiver. (3) Connect the equipment into an outlet on a circuit different  
from that to which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for help. Any special  
accessories needed for compliance must be specified in the instruction.  
6
.ꢀIf an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at  
least one piece of equipment from the battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker is depressed and  
then turn the UPS on.  
Making  
To make  
1. Complete and return the CyberPower Warranty Registration Card, or provide reasonable proof of purchase (for example,  
that establishes you as the Initial Customer (the original end-user consumer purchaser) of the Product and prove that the Product was  
purchased within three (3) years of the event for which you want to make claim for warranty service.  
2. Call CyberPower at (952) 403-9500 or (877) 297-6937 (toll free), write to CyberPower at 5555 12th Ave. East, Suite 110, Shakopee, MN  
5379, or e-mail CyberPower at claims@cyberpowersystems.com, within ten (10) days of the event for which you want to make claim.  
a
Limited Warranty Claim.  
TECHNICAL SPECIFICATIONS  
a
Limited Warranty claim on  
a
Product, you must do the following:  
a
sales receipt)  
7
.ꢀTo maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.  
.ꢀTo store your UPS for an extended period, cover it and store with the battery fully charged. While in storage recharge the battery every  
three months to insure battery life.  
8
Modelꢀ  
CP900Dꢀ  
CP1000Dꢀ  
CP1200Dꢀ  
CP1285Dꢀ  
CP1500D  
a
Capacityꢀ  
900VA  
/
560Wꢀ 1000VA  
/
580Wꢀ 1200VA  
/
720Wꢀ  
1285VA  
/
750Wꢀ 1500VA  
/
900W  
5
a
Input Voltage on Utilityꢀ  
Input Frequencyꢀ  
/
90V to 140V  
3. When you contact CyberPower, identify the Product, the Purchase Date, and request Return Materials Authorization (RMA) information  
from CyberPower.  
60 Hz  
±
3
Hz  
4.  
Pack and ship the Product to CyberPower as instructed in your RMA. Show the RMA code on the shipping label or include it with the  
CAUTION: A shielded-type power cord is required in order to meet FCC emission limits and also to prevent interference to the nearby radio  
and television reception. It is essential that only the supplied power cord be used. Use only shielded cables to connect I/O devices to this  
equipment.  
CAUTION: Any changes or modifications not expressly approved by the guarantee of this device could void the user’s authority to operate  
BASIC OPERATION  
On-Battery Output Voltageꢀ  
Transfer Timeꢀ  
120Vac  
±
5%  
Product. You MUST prepay all shipping costs and you are responsible for packaging and shipment.  
CyberPower will inspect and examine the Product within ten (10) days of receipt. If the Product is not as warranted, CyberPower will repair  
or replace the Product and return it to you at CyberPower's expense, or, if CyberPower is unable to or decides not to repair or replace the  
Product (if defective) within a reasonable time, CyberPower will refund to you the full purchase price you paid for the Product (purchase  
receipt showing price paid is required).  
4ms Typical  
DESCRIPTION  
the equipment.  
Max. Load for UPS Outletsꢀ  
900VA  
560Wꢀ 1000VA  
/
580Wꢀ 1200VA  
/
720Wꢀ  
1285VA  
/
750Wꢀ 1500VA  
/
900W  
1
Power Switch  
Can be used as  
Power On Indicator  
This LED is illuminated when the utility condition is normal and the UPS outlets are providing power, free of surges.  
Using Battery Indicator  
This LED is illuminated when the unit is running in the backup condition.  
1
a
master on/off switch for equipment connected to the battery power supplied outlets.  
Max. Load for Full-Time  
12 Amps  
If you are the Initial Purchaser and the ProducCt OisN  
N
s
tilE  
CcoTvE  
DreEdQ  
UyIPthMeELNimTiGteUdAWRaArNraTnEty  
, the Connected Equipment Guarantee provides  
E
Surge Protection outlets (8 Outlets)ꢀ  
l
e
b
3
5
24  
2
protection for damage to equipment connected to the Product ("Connected Equipment"), subject to certain terms and limitations.  
The Connected Equipment Guarantee is not "first dollar" coverage. It is secondary. If you have any other source of payment for your loss,  
such as insurance, another warranty, or an extended warranty or purchase protection plan (“Primary Coverage”), CyberPower’ will pay only  
to the extent that that the Primary Coverage does not cover the loss. CyberPower's obligation is reduced by any amounts that you are  
On-Battery Output Wave Formꢀ  
Operating Temperatureꢀ  
Simulated Sine Wave Form  
3
+
32°F to 95°  
to 95% NON-CONDENSING  
13 1/8” 4” 7/8”ꢀ  
33.3 10.0 24.9cmꢀ  
24.4 lbsꢀ  
hours typical from total discharge  
F / 0° C to 35° C  
Operating Relative Humidityꢀ  
0
entitled to recover from the Primary Coverage, whether or not you make  
The Limited Warranty does not cover Connected Equipment, but as is explained below, to be covered under the Connected Equipment  
Guarantee, the Connected Equipment must have been damaged due to failure of the Product. The Connected Equipment must have been  
damaged due to defect in materials or workmanship of the Product  
a claim for recovery under any applicable Primary Coverage.  
4
AVR Indicator  
This LED is illuminated when the unit is running in the AVR mode.  
Over Load Indicator  
This LED is illuminated when the unit is overload. You will need to reduce the load.  
Battery and Surge Protected Outlets  
The unit has four battery powered/surge protected outlets for connected equipment and insures temporary  
uninterrupted operation of your equipment during power failure.  
Full-Time Surge Protection Outlets  
The unit has four always on surge suppression outlets.  
Electrical Wiring Fault Indicator  
This LED indicator will illuminate to warn the user that  
this is illuminated, user is advised to disconnect all electrical equipment from the outlet and have an electrician check to ensure the outlet is  
properly wired. The unit will not provide surge protection without being plugged into grounded and properly wired wall outlet.  
Communication Protection Ports  
Communication protection ports will protect any standard modem, fax  
Circuit Breaker  
Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection.  
Serial/USB Ports to PC  
The ports allow connection and communication from the USB or DB-9 serial port on the computer to the UPS unit. The USB port will  
communicate with PowerPanel™ Personal Edition and the DB-9 port is for use with serial cable and the Microsoft UPS Service.  
x
x
9
9
12  
11  
8
Sꢀize (L  
x
W
x
H)ꢀ  
x
x
a
5
Net Weightꢀ  
22.2 lbsꢀ  
25.6 lbs  
a
13  
In the event of damage to the Connected Equipment, your exclusive remedies, and CyberPower’s sole obligations, are as follows for  
Connected Equipment. If (a) the Product purchased and owned by you is defective in material or workmanship; (b) the Limited Warranty  
requirements have been met (except that the three year limitation of the Limited Warranty does not limit the Connected Equipment  
Guarantee, which is for the lifetime of the Product), and; (c) none of the limitations or exclusions on warranty coverage apply (or than the  
three year limit), CyberPower will (as CyberPower elects, as permitted by law), repair, replace, or pay the Agreed Damage Amount (defined  
below) for, the item(s) of your electronic equipment directly and properly connected to the product (the "Connected Equipment") if that  
6
10  
Typical Battery Recharge Timeꢀ  
Typical Battery Lifeꢀ  
Battery Typeꢀ  
8
3ꢀto  
6
years, depending on number of discharge/recharge cycles  
Spill-proof, Maintenance-free, sealed lead-acid  
a
7
Safety Approvalsꢀ  
ꢀUL1778(UPS), cUL107., FCC/DoC Class B  
6
7
C12o0nnveocltte  
d
p
owEeqruilpinmesenint isthe(x)UdnaitmedagSetadtebsy aA  
C
n
dp  
Ca  
o
w
n
e
ardlain,eortrbaynstireanntssi,esnptsik,essu,rgoerssuorrgsepsik  
o
e
n
spornop  
s
etarlnydianrsdtatleleledp, hgoronuenedqeudi,pam  
n
e
d
ntcolindees-c,o  
or  
m
pBlia  
a
s
n
et  
8
EXPECTED RUNTIME IN MINUTES  
(Due to the differences in computer components, the runtime will vary.)  
10/100T Ethernet lines that are properly installed and connected (a "Power Disturbance") and (y) is directly plugged into and properly  
connected to CyberPower Product in its original condition which is properly operated when Power Disturbance passes through the  
CyberPower Product and (y.1) exhausts the protection capacity of the CyberPower Product or (y.2) damages the CyberPower Product. This  
provision sets out the only liability of any character of CyberPower for direct, indirect, special, consequential, and/or incidental damages  
under our Limited Warranty, applies only to Connected Equipment, and all such Liability is limited to the Agreed Damage Amount.  
a
wiring problem exists, such as bad ground, missing ground or reversed wiring. If  
a
a
a
Modelꢀ  
iMacG4ꢀ  
Desktop PC  
Desktop PCꢀ  
Desktop PC  
Desktop PC  
9
with LCD Monitorꢀ  
75 minutesꢀ  
75 minutesꢀ  
90 minutesꢀ  
90 minutesꢀ  
100 minutesꢀ  
with 15” Monitorꢀ  
with 17” Monitorꢀ  
40 minutesꢀ  
40 minutesꢀ  
50 minutesꢀ  
50 minutesꢀ  
58 minutesꢀ  
with 21” Monitor  
35 minutes  
35 minutes  
42 minutes  
42 minutes  
48 minutes  
,
telephone line, broadband network or Ethernet connection.  
CP900Dꢀ  
105 minutesꢀ  
105 minutesꢀ  
145 minutesꢀ  
145 minutesꢀ  
170 minutesꢀ  
60 minutesꢀ  
60 minutesꢀ  
66 minutesꢀ  
66 minutesꢀ  
75 minutesꢀ  
Making Connected Equipment Guarantee Claim.  
a
10  
CP1000Dꢀ  
CP1200Dꢀ  
To make a Warranty claim for damage to Connected Equipment under the Connected Equipment Guarantee, you must do the following:  
1. Complete and return the CyberPower Warranty card or provide reasonable proof of purchase, for example,  
establishes you as the original end-user consumer purchaser of the Product.  
a sales receipt that  
11  
2. Call CyberPower at (952) 403-9500 or (877) 297-6937 (toll free), write to CyberPower at 5555 12th Ave East, Suite 110, Shakopee, MN  
CP1285Dꢀ  
55379, or e-mail CyberPower at claims@cyberpowersystems.com within ten (10) days of the date of the event for which you wish to make  
claim for warranty service.  
a
a
CP1500Dꢀ  

In addition to the user manual CyberPower CP1000D, we also provide a support panel to help you solve your problems with CyberPower CP1000D. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with CyberPower CP1000D. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with CyberPower CP1000D - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.