User manual Sony EXWAVEPRO SNC-CS20

If you found this page, you probably have a problem and you need a user manual for the device Sony EXWAVEPRO SNC-CS20. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Sony EXWAVEPRO SNC-CS20 it belongs to the category Security Camera. A user manualSony EXWAVEPRO SNC-CS20 is taken from the manufacturer, a Sony company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Sony EXWAVEPRO SNC-CS20 directly. You can view the user manualSony EXWAVEPRO SNC-CS20 directly online or save and store it on your computer.

4
-107-639-11 (1)  
Notes on Use  
About the Supplied Manuals  
Installation Manual (this document)  
This Installation Manual describes the names and functions of parts and controls  
of the Network Camera, gives connection examples and explains how to set up  
the camera. Be sure to read the Installation Manual before operating.  
Rear  
LAN port (RJ-45)  
Data and security  
You should keep in mind that the images or audio you are monitoring may be  
protected by privacy and other legal rights, and the responsibility for making  
sure you are complying with applicable laws is yours alone.  
Connect to a hub on the 10BASE-T/100BASE-TX network using a network  
cable (UTP, category 5).  
Refer to “Connecting the power source”on the reverse side for PoE  
connection.  
I/O (Input/Output) port  
This port is used as a sensor input and alarm output terminals.  
Pin assignment  
Access to the images and audio is protected only by a user name and the  
password you set up. No further authentication is provided nor should you  
presume that any other protective filtering is done by the service. Since  
the service is Internet-based, there is a risk that the image or audio you are  
monitoring can be viewed or used by a third-party via the network.  
SONY IS NOT RESPONSIBLE, AND ASSUMES ABSOLUTELY NO LIABILITY TO YOU  
OR ANYONE ELSE, FOR SERVICE INTERRUPTIONS OR DISCONTINUATIONS OR  
EVEN SERVICE CANCELLATION. THE SERVICE IS PROVIDED AS-IS, AND SONY  
DISCLAIMS AND EXCLUDES ALL WARRANTIES, EXPRESS OR IMPLIED, WITH  
RESPECT TO THE SERVICE INCLUDING, BUT NOT LIMITED TO, ANY OR ALL  
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR  
PURPOSE, OR THAT IT WILL OPERATE ERROR-FREE OR CONTINUOUSLY.  
Always verify that the unit is operating properly before use. SONY WILL NOT  
BE LIABLE FOR DAMAGES OF ANY KIND INCLUDING, BUT NOT LIMITED TO,  
COMPENSATION OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF PRESENT  
OR PROSPECTIVE PROFITS DUE TO FAILURE OF THIS UNIT, EITHER DURING THE  
WARRANTY PERIOD OR AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY  
OTHER REASON WHATSOEVER.  
Easy Setup Guide for the Sony Network Camera (stored in  
the CD-ROM)  
The Easy Setup Guide shows you how to set up the camera in order to view the  
image shot by the camera on a computer.  
After installing and connecting the camera following the Installation Manual,  
perform setup using the Easy Setup Guide.  
Network Camera  
Pin No.  
Assignment  
Installation Manual  
1
2
3
4
5
6
Alarm output 1–  
Alarm output 1+  
Alarm output 2–  
Alarm output 2+  
Sensor input – (GND)  
Sensor input +  
Before operating the unit, please read this manual thoroughly and  
retain it for future reference.  
User’s Guide (stored in the CD-ROM)  
The User’s Guide describes how to set up the camera and how to control the  
camera via a Web browser. Operate the camera referring to the User’s Guide.  
Using the CD-ROM Manuals  
The supplied CD-ROM disc includes the User’s Guides and Easy Setup Guides for  
this unit in PDF format.  
m(microphone input) jack (minijack, monaural)  
Connect a commercially available microphone. This jack supports plug-  
in-power microphones (rated voltage: 2.5 V DC).  
Preparations  
The Adobe Reader Version 6.0 or higher must be installed on your computer in  
order to use the guides stored in the CD-ROM disc.  
AUDIO IN (audio input) selector  
Select the level of the audio signal to be input to the microphone/line  
input connector.  
LINE: line input level  
MIC: microphone input level  
The factory default setting is MIC.  
If you lose data by using this unit, SONY accepts no responsibility for  
restoration of the data.  
Note  
Operating or storage location  
Do not shoot an extremely bright object (an illumination, the sun, etc.). Also,  
avoid operating or storing the camera in the following locations, as these can be  
a cause of a malfunction.  
If Adobe Reader is not installed, it may be downloaded from the following URL:  
http://www.adobe.com/  
SNC-CM120  
SNC-CS20  
5 (line output) jack (minijack, monaural)  
Connect a commercially available speaker system with a built-in  
amplifier.  
Reading the manual in the CD-ROM  
Extremely hot or cold places (Operating temperature: -10 °C to +50 °C [22 °F to  
22 °F])  
1
Insert the CD-ROM in your CD-ROM drive.  
1
A cover page appears automatically in your Web browser.  
If it does not appear automatically in the Web browser, double-click on the  
index.htm file on the CD-ROM.  
VIDEO OUT selector  
Areas exposed to direct sunlight for a long time, or close to heating  
equipment (e.g., near heaters)  
Close to sources of strong magnetism  
Close to sources of powerful electromagnetic radiation, such as radios or TV  
transmitters  
Locations subject to strong vibration or shock  
Humid or dusty locations  
Locations exposed to rain  
Locations exposed to direct fluorescent light or reflected light from a window  
Locations exposed to inconsistent, flickering light (the image will flicker.)  
Each time you press the selector button, the camera operation mode  
switches from IP mode to NTSC+IP mode to PAL+IP mode cyclically, and  
the VIDEO OUT indicator shows the selected mode. (The factory default  
setting is IP mode.)  
When adjusting the field of view using a video monitor, select the  
appropriate video signal with this selector.  
IP mode: The video signal is not output from the VIDEO OUT connector.  
(VIDEO OUT indicator: off)  
NTSC+IP mode: The NTSC video signal is output from the VIDEO OUT  
connector. (VIDEO OUT indicator: lights in green.)  
2
Select and click on the manual that you want to read.  
This opens the PDF file of the manual.  
2008 Sony Corporation Printed in China  
Clicking an item in the Table of Contents allows you jump to the relevant  
page.  
Notes  
Owner’s Record  
The files may not be displayed properly, depending on the version of Adobe  
Reader. In this case, install the latest version, which you can download from  
the URL mentioned in “Preparations”above.  
The model and serial numbers are located on the top. Record these numbers  
in the spaces provided below.  
Refer to these numbers whenever you call upon your Sony dealer regarding  
this product.  
Ventilation  
To prevent heat buildup, do not block air circulation around the camera.  
PAL+IP mode: The PAL video signal is output from the VIDEO OUT  
connector. (VIDEO OUT indicator: lights in orange.)  
If you have lost or damaged the CD-ROM, you can purchase replacement.  
Contact your Sony service representative.  
Transportation  
Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the United  
States and/or other countries.  
Note  
Model No.  
Serial No.  
When transporting the camera, repack it as originally packed at the factory or in  
materials of equal quality.  
In NTSC+IP or PAL+IP mode, the video and audio signals can be output to  
a computer via a LAN although there are certain restrictions. For details  
of the restrictions, see the User’s Guide.  
DC 12 V/AC 24 V (power input) terminal  
Connect to a 12V DC or 24V AC power supply system.  
VIDEO OUT (video output) connector  
Connect the BNC cable (not supplied) to this connector.  
POWER indicator  
When the power is supplied to the camera, the camera starts checking  
the system. If the system is normal, this indicator lights up. If a system  
error occurs, this indicator flashes every second. In this case, consult your  
authorized Sony dealer.  
WARNING  
Location and Function of Part  
Cleaning  
To reduce a risk of fire or electric shock, do not expose  
this product to rain or moisture.  
Use a blower to remove dust from the lens.  
Use a soft, dry cloth to clean the external surfaces of the camera. Stubborn  
stains can be removed using a soft cloth dampened with a small quantity of  
detergent solution, then wipe dry.  
Front  
Lens  
A vari-focal lens for 1/3 type (SNC-CM120) or 1/4 type (SNC-CS20) is mounted  
as standard equipment.  
To avoid electrical shock, do not open the cabinet. Refer  
servicing to qualified personnel only.  
Do not use volatile solvents such as alcohol, benzene or thinners as they may  
damage the surface finishes.  
Focus ring  
Turn this ring toward N (near) to focus on a closer object. Turn it toward ∞  
(infinite) to focus on a farther object.  
Zoom ring  
Turn this ring toward T for telephoto, or toward W  
for wide-angle.  
WARNING  
This installation should be made by a qualified service person and should  
conform to all local codes.  
Note on laser beams  
Laser beams may damage a CCD. You are cautioned that the surface of a CCD should  
not be exposed to laser beam radiation in an environment where a laser beam device is  
used.  
U (ground) terminal  
This is a ground terminal for the chassis.  
WARNING  
A readily accessible disconnect device shall be incorporated in the building  
installation wiring.  
Regular parts replacement  
Note  
Tripod screw hole  
Use this screw hole when attaching the camera  
Some of the parts that make up this product (electrolytic condenser, for  
example) need replacing regularly depending on their life expectancies.  
The lives of parts differ according to the environment or condition in which  
this product is used and the length of time it is used, so we recommend  
regular checks.  
U1/4”, 20 UNC  
= 4.5 mm - 9 mm  
When 24 V AC or 12 V DC is supplied to the unit, the maximum power  
consumption of the unit is 9W (SNC-CM120) or 7.5W (SNC-CS20). Check  
the maximum allowable power when you connect the unit.  
Fall-prevention wire rope mounting screw hole  
When installing the camera to the ceiling or the wall, secure the supplied  
fall-prevention wire rope to this hole using the supplied shoulder screw.  
Reset switch  
To reset the camera to the factory default settings, turn on the power to  
the camera while holding down this switch with a pointed object.  
ꢀIRIS selector  
Use this selector when adjusting the focus of the lens.  
WARNING (for Installers only)  
Instructions for installing the equipment on the ceiling or the wall:  
After the installation, ensure the connection is capable of supporting at least  
a force of 50 Newtons (N) downwards.  
to a tripod (screw: 1/4”, 20 UNC). You can attach a (ISO standard) (with the  
tripod to either the top or bottom of the camera. screws are fastened)  
Consult the dealer from whom you bought it for details.  
CAUTION for LAN port  
For safety reason, do not connect the LAN port to any network devices that  
might have excessive voltage.  
The LAN port of this unit is to be connected only to the devices whose  
power feeding meets the requirements for SELV (Safety Extra Low Voltage)  
and complies with Limited Power Source according to IEC 60950-1 Second  
Edition.  
Caution  
Phenomena Specific to CCD Image Sensors  
The following phenomena that may appear in images are specific to CCD (Charge  
Coupled Device) image sensors. They do not indicate malfunctions.  
Use the mounting screw whose length is 4.5 mm – 9 mm only. Use of  
other screws may cause improper mounting and damage parts inside  
the camera.  
White flecks  
Lens connector cover  
Use this cover to release the lens connector.  
Lens connector (4-pin socket)  
Although the CCD image sensors are produced with high-precision technologies,  
fine white flecks may be generated on the screen in rare cases, caused by cosmic  
rays, etc.  
Each time you press the selector button, the iris of the lens switches  
between open and normal. (The factory default setting is normal.)  
Power Supply  
Caution for U.S.A. and Canada  
The SNC-CM120/CS20 operates on 24V AC or 12V DC.  
The SNC-CM120/CS20 automatically detects the power.  
When the iris is set to open, the IRIS OPEN indicator and the focus assist  
indicator appear on a monitor screen. When the VIDEO OUT selector is  
set to the NTSC+IP or PAL+IP mode, the indicators are displayed on the  
monitor connected to the VIDEO OUT connector. When it is set to the IP  
mode, the indicators are displayed on the monitor of the computer.  
Supplies power and control signals to an auto-iris lens.  
This is related to the principle of CCD image sensors and is not a malfunction.  
The white flecks especially tend to be seen in the following cases:  
-
when operating at a high environmental temperature  
Use a Class 2 power supply which is UL Listed (in the U.S.A.) or CSA-certified  
- when you have raised the gain (sensitivity)  
- when using the slow shutter  
(
in Canada).  
For details, see “Focus Assist Function” on the reverse side.  
Vertical smear  
NETWORK indicator  
Flashes in green when the camera is connected to the network.  
Goes off when the camera is not connected to the network.  
Caution for other countries  
When an extremely bright object, such as a strong spotlight or flashlight, is  
being shot, vertical tails may be produced on the screen, or the image may be  
distorted.  
The SNC-CM120/CS20 operates on 24V AC or 12V DC.  
The SNC-CM120/CS20 automatically detects the power.  
Use a power supply rated 24 V AC or 12 V DC which meets the requirements  
for SELV (Safety Extra Low Voltage) and complies with Limited Power Source  
according to IEC 60950-1 Second Edition.  
VIDEO OUT (video output) indicator  
The indicator shows the camera operation mode according to the VIDEO  
OUT selector setting. It goes off in IP mode, lights in green in NTSC+IP  
mode and lights in orange in PAL+IP mode.  
Monitor screen  
Vertical tails shown on the image  
For customers in the U.S.A.  
This device complies with Part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
Bright object (e.g., strong spotlight,  
strong reflected light, flashlight, the sun)  
(continued on the reverse side)  
NOTE: This equipment has been tested and found to comply with the limits  
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits  
are designed to provide reasonable protection against harmful interference  
when the equipment is operated in a commercial environment. This  
equipment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instruction manual, may cause  
harmful interference to radio communications. Operation of this equipment  
in a residential area is likely to cause harmful interference in which case the  
user will be required to correct the interference at his own expense.  
Aliasing  
When fine patterns, stripes, or lines are shot, they may appear jagged or flicker.  
You are cautioned that any changes or modifications not expressly approved  
in this manual could void your authority to operate this equipment.  
All interface cables used to connect peripherals must be shielded in order to  
comply with the limits for a digital device pursuant to Subpart B or Part 15 of  
FCC Rules.  
For customers in Canada  
This Class A digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du  
Canada.  
For the customers in Europe  
The manufacturer of this product is Sony Corporation, 1-7-1 Konan, Minato-  
ku, Tokyo, Japan.  
The Authorized Representative for EMC and product safety is Sony  
Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany.  
For any service or guarantee matters please refer to the addresses given in  
separate service or guarantee documents.  
For the customers in Europe, Australia and New Zealand  
WARNING  
This is a Class A product. In a domestic environment, this product may cause  
radio interference in which case the user may be required to take adequate  
measures.  
In the case that interference should occur, consult your nearest authorized  
Sony service facility.  
This apparatus shall not be used in the residential area.  
SNC-CM120  
SNC-CS20  
ATTENTION  
The electromagnetic fields at specific frequencies may influence the picture  
of the unit.  
7
89  
0
qa  
1 2 3 4  
1 2 3  
4
SEE INSTRUCTION MANUAL  
MIC LINE  
LAN  
1
2 3 4 5 6  
VIDEOOUT  
wa  
w;  
ql  
qk  
VIDEOOUT  
qs  
NETWORK  
POWER  
IRIS  
1
DC 12V  
AC 24V  
+
2
CLASS 2 WIRING  
5
6
5 6  
qj  
qh qg qf  
qd  

In addition to the user manual Sony EXWAVEPRO SNC-CS20, we also provide a support panel to help you solve your problems with Sony EXWAVEPRO SNC-CS20. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Sony EXWAVEPRO SNC-CS20. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Sony EXWAVEPRO SNC-CS20 - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.