User manual JBL LSR6328P

If you found this page, you probably have a problem and you need a user manual for the device JBL LSR6328P. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database JBL LSR6328P it belongs to the category Speaker System. A user manualJBL LSR6328P is taken from the manufacturer, a JBL company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device JBL LSR6328P directly. You can view the user manualJBL LSR6328P directly online or save and store it on your computer.

Linear Spatial Reference  
Bi-amplified Studio  
LSR6328P Monitor  
Key Features:  
Advanced Linear Spatial Reference  
design ensures flatter-off-axis response  
for greater clarity at the mix position.  
RMC™ Room Mode Correction  
provides electronic control of room  
modes. User measurement and  
calibration kit available.  
®
Differential Drive technology with  
dynamic braking for extended low  
frequency response and minimal  
power compression.  
Integrated bi-amplification with  
factory calibrated sensitivities.  
Titanium composite high frequency  
transducer with elliptical oblate  
spheroidal waveguide for precise  
pattern control.  
Magnetically shielded high frequency  
transducer minimizes interference  
when used in close proximity to  
video monitors.  
mounting points to facilitate wall mounting. Recessed handles facilitate easy  
positioning of the loudspeaker in the environment and aid in transportability.  
High-Density baffle for high inertial  
ground and low resonance.  
Linear Dynamics Aperture port  
design eliminates port turbulence  
and reduces port compression.  
218F Low Frequency Transducer  
®
The 8" woofer is based on JBL’s patented Differential Drive technology. With  
dual ±.1" voice coils, power compression is kept at a minimum to reduce spec-  
tral shift as output power levels increase. An added third coil located between  
the drive coils acts as a dynamic brake to limit excess excursion and reduces  
audible distortion at maximum levels. The cone is made of a carbon fiber com-  
posite forming a rigid piston and is supported by a soft butyl rubber surround.  
Reinforced enclosure and convenient  
mounting points for mounted  
installation.  
Integral handles facilitate ease of  
positioning.  
0
53TiS High Frequency Transducer  
The high frequency transducer has a ±" composite diaphragm integrated with  
The LSR6328P studio monitor is  
an Elliptical Oblate Spheroidal (EOS) Waveguide with wide uniform dispersion  
that is critical to the smooth spatial response required in today’s working envi-  
ronments. The driver is shielded to minimize the interference when used in  
close proximity to video monitors.  
designed for use in critical stereo and  
multi-channel monitoring applications  
that require exceptional spectral accura-  
cy and high SPL capability. The  
LSR6328P combines the latest in JBL’s  
renowned transducer and system tech-  
nology with psychoacoustically derived  
spatial response criteria, resulting in a  
more accurate studio monitoring refer-  
ence system. In this design process, the  
system’s frequency response over the  
forward listening range (±±15 vertically  
and ±3ꢀ5 horizontally) is optimized, as  
opposed to the conventional approach  
of optimizing the response directly on-  
axis. This design approach involved  
careful component design, selection of  
crossover frequency, and precise baffle  
geometry and detail. The result is a sys-  
tem that can be used for the most criti-  
cal judgements of recording balance,  
image placement, and equalization. The  
matching of the LSR6328P system to the  
listening environment is further  
enhanced through the use of RMC, an  
analysis/correction system that identi-  
fies and corrects response to compen-  
sate for the dominant low frequency  
standing wave in the system’s room  
response. In addition to a rich array of  
performance features, the LSR6328P has  
a reinforced enclosure and integral  
BiT-haemLSpR6l3ifi28ePdcoPmobiwnees rtwSoyhsigthempower ampliers with an active dividing  
network. Included are over 21ꢀ watts of continuous low frequency power and  
±2ꢀ watts for the high frequency section. The active dividing network produces  
a 36/dB-per-octave Linkwitz-Riley type response for smooth transition between  
transducers, both in the frequency and time domains. This results in exceptional  
imaging and a lack of time smear, and the circuitry also yields a tonal-artifact-  
free noise floor.  
InUpseurtadSjuesntmseintitsviintcyluadenldeveElqcaulibarlaitzioantiseottnin:gs for use with professional  
and semiprofessional equipment, as well as fine tuning with variable level trim.  
Neutrik “Combi” input receptacles accommodate both XLR and ¼" connectors,  
either balanced or unbalanced. DIP switch ± inserts a variable input trim for up  
to ±3 dB of input attenuation. DIP switches 2 & 3 allow selection of either  
-±ꢀ dBV, +4, or +8 dBu calibrated input sensitivities on the ¼" or XLR inputs. A  
Very Low Frequency (VLF) high-pass filter provides protection from excess  
woofer excursion at maximum playback levels. DIP Switch 4 disables this filter  
providing slightly extended deep bass response below the enclosure port tuning  
and allowing the user to observe cone motion caused by sub-sonic signal.  
Boundary compensation is user-selectable to correct low frequency and mid-  
bass build-up when the speakers are placed close to a corner or wall. Three  
settings (-±.1 dB, -3 dB, -4.1 dB) are provided using DIP switches 1 & 6. DIP  
switches 7 & 8 provide ±.1 dB high-frequency boost and attenuation to allow  
compensation for dull or bright listening environments.  

In addition to the user manual JBL LSR6328P, we also provide a support panel to help you solve your problems with JBL LSR6328P. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with JBL LSR6328P. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with JBL LSR6328P - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.