User manual Novatel GPS-534-C

If you found this page, you probably have a problem and you need a user manual for the device Novatel GPS-534-C. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Novatel GPS-534-C it belongs to the category Stereo System. A user manualNovatel GPS-534-C is taken from the manufacturer, a Novatel company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Novatel GPS-534-C directly. You can view the user manualNovatel GPS-534-C directly online or save and store it on your computer.

GPS-534 and GPS-534-C  
USER GUIDE  
surface, see the Mechanical Drawings section of this guide  
for details on the ARINC-743 mounting pattern.  
SPECIFICATIONS  
RF  
3. Attach the antenna to the surface using the four mounting  
screws supplied. The o-ring compresses and creates a seal  
between the surface and the antenna.  
L1:  
L2:  
LB:  
1575.42 ±13 MHz  
1227.60 ±13 MHz  
1542.50 ±17.5 MHz  
3
dB pass band (typical)  
The GPS-534 is an active  
antenna designed to operate at  
the GPS L1 and L2 frequencies,  
2
1
Out-of-band rejection (typical)  
> 40 dBc  
L1: +4.1 dBic, L2:+3.9 dBic,  
LB: +5.7 dBic  
1
575.42 and 1227.60 MHz and  
across the L-Band from 1525 to  
560 MHz. The GPS-534-C  
Gain at zenith (θ = 90°) (min)  
1
Gain roll-off (zenith to horizon) L1/LB: +8 dB, L2:+8 dB  
version is aircraft certified for  
LNA gain  
40 dB ±3  
Right-hand circular  
1.9 dB  
navigation. This guide provides  
the basic information you need to install and begin using your  
new antenna.  
3
4
5
Polarization  
Ref. # Description  
Ref.#  
Description  
Noise figure (typical)  
Nominal impedance  
VSWR  
1
2
3
534 antenna  
Countersink screws  
Mounting surface  
4
5
O-ring  
50 Ω  
ADDITIONAL EQUIPMENT REQUIRED  
Pre-drilled mounting holes  
< 1.5 : 1  
A device with an antenna input port that both receives the RF  
signal and provides 2.5 to 24.0 VDC to the antenna is required  
to set up the GPS-534. (NovAtel GPS receivers provide the  
necessary power through their antenna RF connectors.)  
POWER  
4. Remove the dust cap from the antenna’s TNC connector.  
Input voltage  
Current  
2.5 - 24.0 VDC  
5
.
Attach the male TNC connector of the coaxial cable to the  
antenna’s TNC connector.  
< 35 mA  
Coaxial cable with a male TNC connector  
PHYSICAL  
Width 76.20 mm (3.000”)  
Length 119.38 mm (4.700”)  
Height 20.00 mm (0.788”)  
INSTALLING THE ANTENNA  
Size  
1
Both the input DC power and the output RF signal flow over a  
single coaxial cable that is connected to the unit's TNC female  
connector.  
Weight  
191 g (6.8 oz.)  
Ref. # Description  
3
4
2
ENVIRONMENTAL  
1
Antenna  
The antenna can be attached to a surface by means of an  
ARINC-743 Bolt Pattern.  
screwed into  
place  
The graphic above shows examples of where the 534 antenna  
may be placed on an aircraft or vehicle (not to scale).  
Maximum altitude  
21336 m (70000 ft.)  
Operating temperature  
Storage temperature  
-55°C to +85°C (-67°F to +185°F)  
-55°C to +85°C (-67°F to +185°F)  
2
3
4
Surface  
TNC connector  
Coaxial cable  
Four screws pass through the housing of the antenna.  
Install the antenna as follows:  
ANTENNA CARE  
RTCA DO-160D, RTCA DO-228,  
MIL-C-5541, MIL-E-5400,  
MIL-I-45208A, MIL-STD-810  
and SAE J1455  
The GPS-534 is designed to withstand the elements, including  
rain, snow, and dust. However, to ensure your antenna performs  
optimally, keep the radome clean and brush off any ice and  
snow. In addition, ensure the TNC connector remains clean and  
dry and replace the dust cap when a cable is not connected.  
Designed to meet these  
standards a  
1
.
.
The antenna is supplied with an o-ring. Place it in the o-ring  
groove of the antenna base.  
6. Attach the other end of the coaxial cable to the antenna input  
port of the receiving device, which must provide power as  
detailed in the SPECIFICATIONS section of this guide. All  
NovAtel GPS receivers provide the necessary power  
through their antenna RF connectors.  
User-supplied o-ring grease can be used to hold the o-ring in  
the groove during installation.  
a. If you purchased the GPS-534-C version, your antenna has  
the full FAA TSO-C144 certification.  
2
Pre-drill the mounting holes and the connector hole on the  

In addition to the user manual Novatel GPS-534-C, we also provide a support panel to help you solve your problems with Novatel GPS-534-C. If you have any questions, you can ask them in the form below. Other users viewing this website will have the opportunity to help you solve your probem with Novatel GPS-534-C. Remember that you can also share the solution. If you solved the problem yourself, please write the solution to the problem with Novatel GPS-534-C - you will surely help many users by doing so.

Have you got problems with your device? Ask a question - our users can help you

No one has added a comment for this device/ user manual.