Wenn Sie auf diese Seite gestoßen sind, dann haben Sie bestimmt ein Problem und benötigen eine Anleitung zum Gerät Dialogic SS7G22. Denken Sie daran zu prüfen, ob es eine Anleitung zu genau diesem Gerät ist, was Sie suchen. In unserer Datenbank gehört Dialogic SS7G22 zu der Kategorie Server. Die Anleitung Dialogic SS7G22kommt vom Produzenten, der Firma Dialogic - es ist ein offizielles Dokument, und wenn Sie irgendwelche Zweifel haben, was den Inhalt betrifft, kontaktieren Sie bitte den Geräteproduzenten Dialogic SS7G22 direkt. Sie können die Anleitung Dialogic SS7G22 direkt online anschauen, oder es auf Ihrem Computer speichern und aufbewahren.

Chapter 2 Introduction  

A list of product variants to which this manual applies can be found in Section 2.11, “Applicability” on  

page 14.  

2.3  

Power Supplies  

An SS7G21 or SS7G22 product can be ordered with one of the following:  

•

•

AC-input Power Supply Cage (SS7G21A, SS7G22A)  

DC-input Power Supply Cage (SS7G21D, SS7G22D)  

The Power Supply Cage, which is mounted towards the left rear of the chassis, contains the Power Supply  

Modules. Both the AC and DC-input Power Supply Cage may contain up to two Power Supply Modules and  

can be configured as follows:  

•

One Power Supply Module installed (this is the factory standard setting). Units configured in this manner  

can supply a fully loaded product, but do not provide dual redundancy. The second position contains a  

filler module.  

•

Two Power Supply Modules installed. Units configured in this manner are dual redundant. In the event of  

a failure of any one Power Supply Module, the operation of the product is unaffected.  

When the product is configured with two Power Supply Modules, the hot-swap feature allows the user to  

replace a failed module without interrupting system functionality.  

Caution: The Power Supply Modules used in the AC-input Power Supply Cage can not be used in the DC-  

input Power Supply Cage. Similarly, the Power Supply Modules used in the DC-input Power  

Supply Cage can not be used in the AC-input Power Supply Cage. The correct product variant  

must be specified at time of ordering, see Chapter 12, “Part Number Reference”.  

2.4  

Server Board  

The chassis incorporates a Server Board incorporating dual Intel Xeon processors with 512 KB L2 cache and  

1

GB DRAM DIMM memory. The Server Board has a Riser Board, which supports the fitting of up to three  

full-length PCI SS7 Signaling Boards. See Section 2.7, “SS7 Signaling Boards” on page 12 for more  

information on the types of SS7 Signaling Boards that are installed.  

2.5  

Hard Disk Drive  

As standard, a Hard Disk Drive (HDD) is installed in a drive bay in the front of the chassis, accessible by  

removing the front bezel of the product. A spare assembly is available for the HDD, see Chapter 12, “Part  

Number Reference”.  

2.6  

CD-ROM Drive  

A CD-ROM drive is accessible at the front panel, and may be used for loading software updates.  

2.7  

SS7 Signaling Boards  

The SS7G21 and SS7G22 use intelligent multi-port interface boards with one or more on-board signaling  

processors for the processing of SS7 signaling links. The SS7 Signaling Boards are full-size PCI form factor  

boards that occupy one, two, or three board positions in a Riser Board mounted on the Server Board. The  

SS7 Signaling Boards each provide four (or two) primary rate telecommunications (PCM) interfaces, each  

being individually configured at run-time under software control to operate as a T1 or E1 interface with  

selectable line code and frame format. For SS7 Signaling Boards with two PCM interfaces, there are also two  

synchronous V.11 (V.35 compatible) serial interfaces, on a shared connector. See Section 6.5, “SS7 Serial  

Interface Ports” on page 36 and Appendix A for more information.  

The number of SS7 signaling links that can be terminated by an SS7 Signaling Board depends on the board  

type as described below. Signaling links may be presented either as a timeslot on an external PCM interface,  

or as a synchronous V.11 serial interface when provided by the board. Signaling links can operate at 64kb/s,  

56kb/s or 48kb/s. The SS7 Signaling Boards also support configurable clock recovery priorities with  

automatic switching to a new clock source on failure, and automatic restoration on recovery of the failed  

clock source.  

1

2

• ← Previous
• Next page →

Außer der Anleitung Dialogic SS7G22, veröffentlichen wir ebenfalls das Hilfspaneel, das Ihnen bei der Lösung der Probleme mit Dialogic SS7G22 helfen wird. Wenn Sie Fragen haben, können Sie sie im unten angegebenem Formular stellen. Andere Nutzer, die hier reinschauen, werden dann die Möglichkeit haben, Ihnen bei der Lösung des Problems mit Dialogic SS7G22 zu helfen. Denken Sie daran, dass Sie auch die Lösung mit anderen Teilen können. Wenn Sie es selbst geschafft haben, fügen Sie bitte hier die Beschreibung und die Lösung des Problems mit Dialogic SS7G22 hinzu - damit helfen Sie bestimmt vielen Nutzern.