このページへお越しの方は、おそらくデバイスTOA Electronics F-160WPに関する問題を抱えており、その説明書を必要としていることでしょう。お探しの説明書がお持ちのデバイスのそれであることを必ずご確認ください、お探しのTOA Electronics F-160WPは、このデータベースではカテゴリースピーカーシステムに属します。 説明書TOA Electronics F-160WPはメーカーTOA Electronicsの発行するものです　－　これは公式文書であるため、その内容に疑問がある場合はデバイスTOA Electronics F-160WPの製造元に直接お問い合わせください。説明書TOA Electronics F-160WPはオンラインで直接見たりコンピュータにダウンロードし保存したりすることができます。

3. HANDLING PRECAUTIONS  

Use optional mounting brackets when mounting the speaker to the ceiling or wall.  

Avoid using the speaker on the beach because the speaker's life can be greatly shortened by sea breezes.  

TOA takes no responsibility for any accident or equipment failure due to inadequate installation places or  

incorrect installation methods or disassembly or modifications carried out for the purposes other than repair  

service.  

The F series speaker is not magnetically shielded. Install it as far away as possible from color televisions or  

video monitors to avoid degradation in television picture quality.  

4

. FEATURES  

Two-way bass-reflex system.  

High efficiency, wide range, and high input power handling capacity.  

F-160 series: High power capacity 13 cm woofer with a large 90 mm magnetic circuit, and high-efficiency  

3

cm dome tweeter with a large 70 mm magnetic circuit.  

F-240 series: High power capacity 16 cm woofer with a large 90 mm magnetic circuit, and high efficiency  

cm dome tweeter with a large 70 mm magnetic circuit and a titanium diaphragm.  

3

The tweeter employs a constant directivity horn which ensures uniform sound dispersion of 90 ° horizontal  

and 90° vertical.  

Independent built-in overload protection circuitry for woofer and tweeter. (Low-impedance models only)  

A detachable rear cover cleanly conceals the speaker terminals.  

Acoustically efficient polypropylene enclosure.  

Optional wall and ceiling mounting brackets.  

F-160WP: Drip-proof construction makes the speaker system ideal for outdoor use.  

5. OVERLOAD PROTECTION CIRCUITRY INFORMATION  

(LOW-IMPEDANCE MODELS ONLY)  

The F-160G, F-160W, F-240G, and F-240W have a built-in overload protection circuitry.  

If the excessive input is applied to a woofer or tweeter, the overload protection circuitry is activated and cuts  

off the signal supply to the speaker component.  

A sudden drop of the volume level of either the high or low frequencies during speaker operation indicates  

that the overload protection circuitry has been activated. In such a case, reduce the amplifier volume and just  

wait. The protection circuitry is automatically reset after approximately 3-30 seconds. After the circuitry is  

reset, set the volume at a lower level than before.  

[Important Note]  

This overload protection circuitry does not perfectly protect the speaker component. Depending upon the  

excessive input to be applied, the protection circuitry may not operate, causing damage to the speaker  

component. In addition, the circuitry may not be restored to the previous state if the excessive input is applied  

continuously for long time. Take special care that the excessive input is not applied to the speaker during use.  

4

• ← Previous
• Next page →

TOA Electronics F-160WPの説明書の他にも、あなたがTOA Electronics F-160WPとその問題を解決するのに役立つヘルプパネルを提供しています。何か質問がある場合は、以下のフォームから送信することができます。他のユーザーがここを訪問し、あなたのTOA Electronics F-160WPに関する問題解決を支援してくれるかもしれません。また、あなたがたどり着いた解決方法についてもご共有することをお忘れなく。うまく解決できた場合はTOA Electronics F-160WPに関する問題とその解決法についてこちらにご記入ください　－　きっと数多くのユーザーに役立つことでしょう。