Handleiding A.O. Smith 101

Als u deze pagina heeft gevonden, heeft u waarschijnlijk een probleem en heeft u waarschaijnelijk de danleiding voor het apparaat A.O. Smith 101 nodig. Controleer dat het een handleiding is voor het apparaat dat u zoekt. In onze databank A.O. Smith 101 behoort het tot de categorie Waterkoker. De handleiding A.O. Smith 101 is afkomstig van de fabrikant, het bedrijf A.O. Smith - het is een officieel document, en als u twijfelt over de inhoud, neem dan direct contact op met de fabrikant van het apparaat A.O. Smith 101. De handleiding A.O. Smith 101 kunt u direct online bekijken of op te slaan op uw computer.

if the blower prover does not activate after 15 seconds. This 5. Press the SELECT KEY.  
time allows the blower relay to activate, the blower to come up  
6
7
. Use the UP and DOWN key to select the value you wish to enter.  
to speed, and the response from the blower prover to be filtered.  
. Press the SELECT key to accept and store the new value.  
User Settings Screen:  
Each setpoint or user setting has either a limited selection of  
values, or a limited range of values. The Up/Down keys are  
used to change values. After changing an item, the Select key  
is pressed to accept the change, or the Menu key is pressed to  
reject the change and restore the item to its original value.  
The following setpoints can be changed:  
High Limit Differential:  
The outlet temperature must be below the automatic High Limit  
setpoint minus the High Limit Differential setpoint before a call  
for heat can be generated.  
HIGH LIMIT DIFFERENTIAL SETPOINT ADJUSTMENT  
PROCEDURE  
Operating Setpoint:  
This setpoint sets the base temperature for the control algorithm.  
The High Limit Differential Setpoint has a range of 1°F to 50°F for  
all models. Use the following procedure to change the High Limit  
Differential Setpoint:  
OPERATING SETPOINT ADJUSTMENT PROCEDURE  
1
2
3
4
. Press the MENU key.  
The system has a standard programmable Operating Setpoint  
range of 70°F (21°C) to 190°F (88°C) for a VW and of 70°F  
. Scrollthe">"withthedownkeynexttoUSERSETTINGSCREEN.  
. Press the SELECT key.  
(
21°C) to 220°F (104°C) for a VB for either a Remote or inlet  
probe depending on selection. The user can easily change  
the Operating Setpoint at any time by using the following  
procedure. When any configuration or setpoint is changed  
. Scroll the ">" with the DOWN key until it is pointing to HIGH  
LIMIT DIFFERENTIAL SETPOINT.  
(
and the Select key touched), the new value is IMMEDIATELY  
saved to non-volatile memory. The factory default setting is  
1
1
2
45°F (49°C).  
5
6
7
. Press the SELECT key.  
. Press the MENU key.  
. Use the UP or DOWN key to select the value you wish to enter.  
. Press the SELECT key to accept and store the new value.  
. Scroll the ">" with the DOWN key next to the USER  
SETTING SCREEN.  
Operating Differential Setpoints:  
3. Press the SELECT key.  
Each of the two stages has an independent Operating  
Differential setpoint.  
4. Scroll the ">" with the DOWN key until it is pointing to  
OPERATING SETPOINT.  
Temperature Units:  
Temperature can be displayed in either °F or °C units.  
5
6
7
. Press the SELECT key.  
. Use the UP or DOWN key to select the value you wish to enter.  
. Press the SELECT key to accept and store the new value.  
Post Circulate Delay Time:  
The time circulation pump will stay on after the burner is  
turned off. The time in seconds is adjustable with the  
following values: 45, 90, 180 or continuous. If the  
continuous value is selected the pump will remain on at  
all times and the post circulate state time will be set at 45  
seconds.  
High Limit:  
The outlet temperature probe contains both an ECO switch  
and a thermistor for temperature measurement. The sensed  
outlet temperature is used for the automatically resettable  
High Limit setpoint. If the sensed outlet temperature exceeds  
the High Limit setpoint, a "soft lockout" condition will occur and  
the burner will be shut off. This fault condition is automatically  
cleared when the temperature drops below the high limit  
setpoint minus the high limit differential.  
Network Address:  
This is a unique number assigned to this boiler to  
differentiate it from other boilers or water heater on the same  
A. O. Smith proprietary network. A valid Network Address  
can be any number from 0 to 31. It is set by default to zero,  
which is an invalid address. The boiler will not communicate  
until it is changed to a valid and unique number. This prevents  
two units from trying to respond to the same request from  
the PC or supervisory network device.  
AUTO HIGH LIMIT SETPOINT ADJUSTMENT PROCEDURE/  
OUTLET TEMPERATURE PROBE  
The High Limit setpoint has a range of 90°F (32°C) to 210°F (99°C)  
for a VW and a range of 90°F (32°C) to 235°F (113°C) for a VB.  
Use the following procedure to change the automatically resettable  
High Limit Setpoint:  
Configuration Settings Screen:  
Displays the status of the dipswitches installed on all  
boards as described earlier.  
1. Press the MENU key.  
Log & System Info Screen:  
2
. Scrollthe">"withtheDOWNkeynexttoUSERSETTINGSCREEN.  
Displays the following information:  
Elapsed hours of operation (Total time system has been  
powered up)  
3. Press the SELECT key.  
4. Scroll the ">" with the DOWN key until it is pointing to HIGH  
LIMIT SETPOINT.  
Number of running minutes (Number of minutes system has  
been in the run mode)  
1
4

Naast de handleiding A.O. Smith 101, bieden wij ook hulp panel die u zal helpen om uw problemen op te lossen met A.O. Smith 101. Als u vragen heeft, kunt u ze in het onderstaande formulier invullen. Andere gebruikers zullen ze zien en kunnen u helpen om uw probleem op te lossen met A.O. Smith 101. Vergeet niet dat u ook de oplossing kunt delen. Als u uzelf het probleem heeft opgelost, plaats hier een beschrijving en uw oplossing met A.O. Smith 101 - u zal zeker de vele gebruikers helpen

Problemen met het apparaat? Stel een vraag - onze gebruikers kunnen helpen

Nog niemand heeft een commentaar voor deze machin/handleiding toegevoegd.