Handleiding Skil 1677M

Als u deze pagina heeft gevonden, heeft u waarschijnlijk een probleem en heeft u waarschaijnelijk de danleiding voor het apparaat Skil 1677M nodig. Controleer dat het een handleiding is voor het apparaat dat u zoekt. In onze databank Skil 1677M behoort het tot de categorie Zaag. De handleiding Skil 1677M is afkomstig van de fabrikant, het bedrijf Skil - het is een officieel document, en als u twijfelt over de inhoud, neem dan direct contact op met de fabrikant van het apparaat Skil 1677M. De handleiding Skil 1677M kunt u direct online bekijken of op te slaan op uw computer.

BM 1619X01743 08-06 8/17/06 8:48 AM Page 3  
Tool Use and Care  
other condition that may affect the tools  
Use clamps or other practical way to operation. If damaged, have the tool  
secure and support the workpiece to a serviced before using. Many accidents are  
stable platform. Holding the work by hand caused by poorly maintained tools. Develop  
or against your body is unstable and may a periodic maintenance schedule for your  
lead to loss of control.  
tool.  
Do not force tool. Use the correct tool for Use only accessories that are  
your application. The correct tool will do the recommended by the manufacturer for  
job better and safer at the rate for which it is your model. Accessories that may be  
designed.Do not use tool if switch does suitable for one tool, may become hazardous  
not turn it “ON” or “OFF”. Any tool that when used on another tool.  
cannot be controlled with the switch is  
Service  
dangerous and must be repaired.  
Tool service must be performed only by  
qualified repair personnel. Service or  
maintenance performed by unqualified  
personnel could result in a risk of injury. For  
example: internal wires may be misplaced or  
pinched, safety guard return springs may be  
Disconnect the plug from the power  
source before making any adjustments,  
changing accessories, or storing the tool.  
Such preventive safety measures reduce the  
risk of starting the tool accidentally.  
Store idle tools out of reach of children improperly mounted.  
and other untrained persons. Tools are  
When servicing a tool, use only identical  
replacement parts. Follow instructions in  
dangerous in the hands of untrained users.  
Maintain tools with care. Keep cutting the Maintenance section of this manual.  
tools sharp and clean. Properly maintained Use of unauthorized parts or failure to follow  
tools, with sharp cutting edges are less likely Maintenance Instructions may create a risk  
to bind and are easier to control. Any of electric shock or injury. Certain cleaning  
alteration or modification is a misuse and agents such as gasoline, carbon  
may result in a dangerous condition.  
tetrachloride, ammonia, etc. may damage  
plastic parts.  
Check for misalignment or binding of  
moving parts, breakage of parts, and any  
Safety Rules for Circular Saws  
Keep hands away from Do not reach underneath the work. The  
cutting area and blade. Keep guard cannot protect you from the blade below  
!
DANGER  
your second hand on auxiliary handle, or the work. Do not attempt to remove cut material  
motor housing. If both hands are holding the when blade is moving.  
saw, they cannot be cut by the blade. Hold the  
Check lower guard for proper closing before  
saw firmly to prevent loss of control. Figures in  
each use. Do not operate saw if lower guard  
this manual illustrate typical hand support of the  
does not move freely and close instantly.  
saw. NEVER place your hand behind the saw  
Never clamp or tie the lower guard into the  
blade since kickback could cause the saw to  
open position. If saw is accidentally dropped,  
jump backwards over your hand.  
lower guard may be bent. Raise the lower guard  
Keep your body positioned to either side of only with the Lower Guard Lift Lever and make  
the saw blade, but not in line with the saw sure it moves freely and does not touch the  
blade. KICKBACK could cause the saw to jump blade or any other part, in all angles and depths  
backwards. (See “Causes and Operator of cut.  
Prevention of Kickback.”)  
-
3-  

Naast de handleiding Skil 1677M, bieden wij ook hulp panel die u zal helpen om uw problemen op te lossen met Skil 1677M. Als u vragen heeft, kunt u ze in het onderstaande formulier invullen. Andere gebruikers zullen ze zien en kunnen u helpen om uw probleem op te lossen met Skil 1677M. Vergeet niet dat u ook de oplossing kunt delen. Als u uzelf het probleem heeft opgelost, plaats hier een beschrijving en uw oplossing met Skil 1677M - u zal zeker de vele gebruikers helpen

Problemen met het apparaat? Stel een vraag - onze gebruikers kunnen helpen

Nog niemand heeft een commentaar voor deze machin/handleiding toegevoegd.